Redundancy lost SMH SNMP Agents Windows server 2012 r2
Hi. I have a DL360 Gen9 that i have connected 2 nics to seperate Cisco switches and configured a Windows teaming adapter (windows server 2012 r2) and in the Microsoft teaming tool everything is OK and...
View ArticleDL580 G7 overheat temperature sensor 17
We have a DL580 G7 that shut down due to "overheating" and since then turns off 1 second after poweron for the same reason. I'm pretty sure that nothing can be overheating after 1 second, at that point...
View ArticleHow to enable IPMI on DLxxx servers?
I have DL320 G6 and DL160 Gen9 and they are not listening on IPMI port event the service is enabled. Is it somehow licensed? Or how to enable it?
View ArticleError 267 after changing internal controller to SmartArray.
Hello! I bought HP Proliant DL60 base (with B140i) with optional HP H240 Smart Array Controller. At start i configure RAID 5 with 3 SATA Drive on B140i, then i install HP H240 and connect all disk to...
View ArticleCannot restore Intelligent Provisioning on DL310 Gen8
Have had a new DL310 Gen8 V2 for 1 week. Â I'm using in a lab envioronment to simulate 911 center servers that my company installs. Â After several successful Windows OS installs, I can no longer run...
View ArticleML350 G5 Will not boot
I have an ML350 G5 running Windows Server 2003 x64. Recently the server crashed and now when booting I get Windows/System32/Config is missing... I attempted to do a repair using the OS install media...
View ArticleWindows Raid driver
I am trying to recover full Windows Server2012 R2 restore from a Windows Backup's bare-metal backup.With Intelligent Provisioning, I could find a way to boot from Windows CD but never see hardware RAID...
View ArticleSwapping SA 431 and SA 3200
Can someone shed some information if there would be performance gain to what I'm planning to do?We have a Smart Array 3200 with Ultra3 drives in an ML370G1 and an SA 431 with Ultra2 drives in an...
View ArticleNOT RECOGNISED ARRAY CONTROLLER FOR NT TERMINAL SERVER
I am attempting to install NT Terminal Server onto a Proliant ML530 server. NT 4.0 Server OS was installed previously and used the Smart Array 4200 Controller. However, when I try to install Terminal...
View ArticleRapid Server RECOVERY
Hi, I have recently purchased 2 dl380's These are to be configured as cold stanby systems. Due to application problems clustering would not work so for 24*7 we went for redundant power supplies plus...
View ArticleProblem configuring Array from NT
I have setup a DL580 with NT4 (SP6A) using the onboard RAID controller for internal disks to support NT. I have installed a 64bit/66MHz fibre adapter and connected this to a 7 port fibre hub. Attached...
View ArticleMixed disks on same port SCSI
We need to install a Proliant ML570, on this machine we have 2 arrays of 6 disks. Can we mixed 2 x 9 Go in Raid 1 et 4 x 72 Go in Raid 5 in the same array ? Or are we obliged to put 6 x 72 Go ? Thank you.
View ArticleDiffering RPMs on disk drives
Looking for advice on adding drives to my Proliant ML370, Compaq Smart Array 431 controller. I have four 9.1 gb, wide ultra 2, 7200 RPM drives in the array and I want to add two more. I find I am...
View ArticleBoot from Storage with SA5300
I have a Smart Array Controller 5300 with latest FW running in Slot 2 of a DL380 G3 Server (all FW updated) connected to a HSG80.Onboard 5i controller is disabled.OS is to be W2K-Server english.I want...
View ArticleStorage drivers for Netware 5
We adquire a Proliant ML350 G3 Server to make a transition from a Netserver E50. We have Netware 5. Now when we tried to install Netware 5 in the Proliant Server, it doesn't recognize the currect...
View ArticleCluster Storage - 2 servers same disk space sharing problem
HiI installed Shared Cluster Storage, connected 2 DL380G3 servers to it (using 5312 SCSI controllers, not built-in 5i). I didn't connect servers to each other using the provided cross-over cable...
View ArticleUpgrade procedure for 431 to 4200
Does anyone know the upgrade procedure for a 431 controller to 4200?Running on a proliant ml350 w/ 3 X 36 GB Drives.
View Article2sl - giving error 26 -may have a disk problem rerun acu
I have installed a 2-sl into cpq ml350 with raid 0+1 on 2 x 36g drives -When i boot from smart start to create partition etc. I get an error stating that the disk cannot be accessed , it may have a...
View ArticleProblems to update the latest firmware 5312 in a DL368G3
Hi,we have a problem to update the firmware of a smartarray 5312 in a dl380g3 server through the SmartStart Maintenance (ROM Update Utility). We have downloaded the latest (3.40 B date 2 Oct 03)...
View ArticleSMART 5i, SMART Array Cluster Storage and 1775 error
Anyone any ideas on this one.We have a DL380 G2 packaged cluster which worked fine for MS Clustering, using the SMART Array Cluster Storage.We then moved the internal server drives into the external...
View Article