3rd Party SATA solutions?
Figuring you can get 1TB SATA drives nowadays for around $100 dollars, what are the chances of it working with a HP ML350 G5? I know reliability might be an issue but it's used mostly for low access...
View ArticleHow to install 2nd hdd in Proliant ML150 server
I've purchased a 2nd non-hotswap SCSI hdd for this server. Can I use the same controller and ribbon that's connected to 1st hdd or do I need a 2nd controller? Thanks P.S. This thread has been moevd...
View Article1467GB, SCSI, BD1468A4B5, Service Hours N/A
Hello,i have a ProLiant DL360G3 with two HP Harddrives. 1=BF1468B26B (HPB9) and 2=BD1468A4B5 (HPBC).Drive 1 shows on the SMH no Service Hours, Secrors Read, Sectors Written and so on.At Service Hours...
View ArticleHard Drive life time ?
Hi,Where can i find the time sime my hard drive is working ? I can't found it in ADUThx P.S. This thread has been moved from Disk to ProLiant Servers (ML,DL,SL). - Hp forum Moderator
View ArticleDisk Utilization is 100%
My server is DL 380G4. Bay 0,1,2,3 are using RAID 5 for file storage and 4,5 is RAID 1 for operationg system my OS is Novell OES with SP1.Last couple days i receive Disk Utilization is 100% error from...
View ArticleHP Proliant DL360 G7 not picking up SAN connected via SCSI
HI there GuysI am having a problem with my Hp proliant server picking up the SAN unit.I have installed a new HP SC11Xe Host Bus Adaptor.The BIOS does see the card but when i boot from the smart start...
View ArticleAre the 300GB 6G SATA Value Endurance SSDs appropriate for mission critical...
Hello,I am an IT consultant to an SME, as I advise them on IT issues, namely IT server infrastructure.They are in the process of upgrading some systems and I recommended them to buy a HP Proliant...
View Article10gBase-T NIC needed for Proliant DL385 G7
Hi, Can someone recommend a 10gBase-T NIC (RJ-45) for our Proliant DL385 G7 server please?The ones that HP makes looks like they are only compatible with the Gen 8 models. thanks in advance.
View ArticleDL180 No Post / BMC Blinking, all leds Green
Hi, i will describe the issue hoping to find an answer because I'm about to go crazy, I have a DL180 G6 with 1 proc. 2 DIMMS on position A2 B4 like it says on the manual, a month ago a fan failed...
View ArticleiLo on DL160se G6 stops working..
Anyone out there have an issue with iLo on the Dl160se G6 servers?Specifically iLo webpage stops working. You can pin gthe iLo IP address but you cannot get to the website to do any config or KVM work....
View Articleperformance counters on SL2x170
We would like to use performance counter on our new cluster consisting of SL2x170 nodes with Westmere processors. Patching the official RHEL 5.5 kernel (based on 2.6.18) with the performance counter...
View ArticleSL170z RAID controller
I want to use SAS drives in my SL170z and wonder if the Smart Array P212 is a good choice? I have no need for raid 5. Do I need one controller for each node, or will one controller support the drives...
View ArticleSL2x170z G6 - Need info how to change serial number of new system board....
I just replaced a new system board for SL2x170z G6 server. Could not find any documentation for serial number replacement and the PID. Normally, on other HP servers, F9 on the BIOS will show up during...
View ArticleUpgrade hard disk on DL320 g5 from raid 72gb to 250gb
Our server has already installed two 72GB Sata harddisk.Our planning is to upgrade to two 250GB harddisk.I have done this procedure:i had unplug one of thr 72gb HD, after i plug in one of 250gb HD and...
View ArticleML150 G3 SCSI BIOS not installed when adding two SATA drives
Hi,I wanted to post/share if anyone has had any similar experience. Our HPML150 G3 runs Server 2003 using two SCSI disk controllers with four SCSI drives. I just added two SATA controllers and two...
View ArticleReplaced 146.8 drive on DL360
I had a failed drive and had a new one shipped from HP. When I insert the new drive it fails when the array controller starts up the mirror before the OS loads. In Insight it is showing the new drive...
View ArticleAdding capacity to ML330 G6
Hi all, I have a HP Proliant ML330 G6 which has a P410 raid controller, at present it is fitted with two dual port 300 gb SAS drives, my question is can I add two more drives and set them up as a...
View ArticleAfter creating the second Array, windows doesen't boot anymore
Hi,I have a test system DL380g5 with a p400i ctrl with 2 disks (Boot Raid1)for windows 2008r2 and 6 disks (raid5). There is a problem after creating the second array B and create the logical disk, it...
View ArticleXenserver 6.2 on ProLiant ML310e Gen8 v2
We want to install Xenserver 6.2 on a new cheap ProLiant ML310e Gen8 v2. The Xenserver install software cannot see the harddisk of the ProLiant. Anybody with a solution or driver for this problem ? (I...
View ArticleAdding discs in ProLiant DL380 G5 server
HelloI am having an HP ProLiant DL380G5 and I want to add 3 extra drives. The first 2 of them in RAID 5 and the 3rd one as an extra physical one. Can you explain me the procedure? Is there a way to...
View Article