Nic Teaming (or something similar) across multiple servers?
HI , I'm looking to implement a solution where I have two HP servers, I want one of the servers to take over when the other fails , I need to work it so that the server that takes over has the same IP...
View ArticleB110i RAID ARRAY
Hi, I have a server with a RAID 1 array set up using 2 500GB Hard drives. I want to increase the hard drive size to 2TB and was wondering what the best way to do this. I have already replaced the hard...
View ArticleHP Support site for older servers
Dear all,I have recently changed jobs and its been a few months since I've needed to download anything for Proliant servers from the support site.Just gone to find something for a customers old DL360...
View Articleupgrade or renew
Hi, I'm getting conflicting advice on our "ancient" proliant g5. I've been told it can be upgraded and the new windows server and sage 200 suite can be installed with no issues and there would be...
View Articleserver ProLiant DL320 G5p problem select to boot hdd1 or hdd2
Hi, I have aproblem,I havefour hdd,can not figure outhowto choose theminthe BIOSto boot? For example: selectdisk 1 in bios -to bootfrom disk1, select disk 2 - systemis loadedfrom disk2 ... Nowbootthe...
View ArticleLocating ProLiant ML150 G6 Drivers, Firmware, BIOS Updates etc.
I've been using Windows on this ML150 for years now without issue. I have 4 drives attached to the 4 black SATA ports, and after installing the Windows drivers here, all drives were usable. (This...
View ArticleDL380 GEN8 installling oeratiing system probelem
HiI use Intelligent Provisioning to istall windows 2008 server R2 64 bit in DL380 GEN8 SERVER but when i finsh the wizrd it stay in sizing opeating system files stage !!!!!I set the array 3 H.D.D RAID...
View ArticleCannot locate drivers for ML350 G5 Server
Hi, when i visit the Drivers, Software & Firmware for HP ProLiant ML350 G5 Server i get an error when i type my serial The product you selected is not supported by HPSC or is not a valid...
View ArticleNetwork problem in a guest domain cotroller
On a DL360 Gen 8 deployed Microsoft Hyper-V Server 2012 R2. On the Hyper-V server deployed guest domain controller Windows Server 2012 R2. Guest server uses a virtual switch (Microsoft). Response time...
View ArticleHP Smart Array p410 change RAID 0 to RAID 1
Hello. We have in our company server Hp Proliant DL 180G^ with HP Smart Array p210. Also we have 2 disks SAS 140GB in RAID 0 and 2 disks SATA 1TB in RAID 0. Last time we have problems with SATA disks...
View ArticleProliant ML150 G2 Turns itself off after power-on
Hi everyone,I have a proliant ml150 g2, and 2 70 gig disks in stripe 0 mode.... (adaptec aic-7901x controller).the problem is that i can't access data , because my server a few days ago just in the...
View ArticleNo ILO console screen on DL380p Gen8 with installed Quadro K4000
Hi All, Does anyone knows how to get image on ILO console (with advanced license) when Quadro K4000 card is installed?Currently I can only get image on DVI port on Quadro K4000, VGA out on server board...
View ArticleDL180G6 network card nc362i problem
ServerDL180g6 CZJ94107XZ,itbuilta network cardnc 362i (2 ports) PCI \ VEN_8086 & DEV_10C9 & SUBSYS_323F103C & REV_01For some reason,onecardturned intooperation10Mbper...
View ArticleReceived a consumer quality HDD instead of an enterprise quality HDD for my...
Hi guys, Not too sure anyone face the same "problem" like i do. As i'm currently using an ML110 G6 server purchased with 2 x 250gb WD RE3 enterprise storage sata drive. Sadly, one fine day one of the...
View ArticleHow to run SSA on Windows?
Hi On a ML350p G8 with Windows 20012 R2 installed, how do you run the SSA (what was ACU) from the GUI/desktop? I know you can press F5 on boot but I want to access it with rebooting the Server....
View ArticleDl140 g3 Intel VT problems.
Hello!I have a problem with 1 of 2 servers Proliant DL140 g3 (bios 1.18 - last )5140 Hot Plug SATA/SAS (Rack1U XeonDC 2.33Ghz(4Mb)/8x4gb(32) /SAS RAID(1/0)/noLFF HDD(2)/noCD.noFDD/2xGigEth, 36GB 15k...
View ArticleDL160 G6 lights-out 100 credentials lost
Hello guys, I'm back to this forum because I'm facing an issue and my server. I just got a old DL160 G65 for lab purposes but I don't have the iLO credentials. I tried to set the admin password with...
View ArticleHP Proliant DL380e G8 - 1798-Slot X Drive Array - Cache Module Self-Test...
Hello I recently bought a Hp proliant DL380e G8, which has just 1 month of use. When I turn it on is reporting an error from the disk controller (HP Smart Array B320i Dynamic): I have read the document...
View ArticleML 570 will not boot - non-system disk or disk error
Hi, I received an old Proliant ML570 and want to start it up. (It has 5 Ultra2 scsi harddisks in it).I am not a specialist in hardware.The servers starts (in the machine alle leds are green) but on the...
View ArticleMl110 G6 fan failure
Hi Is it normal for our ML110 G6 server to shut down when a fan fails?When we boot with only the CPU fan working it's noisy, continues to boot for around 50 seconds then shuts down withthe amber fan...
View Article