memory upgrade problem ml110 g7

August 9, 2016, 9:09 am

≫ Next: HP SUM 7.5.1 - Admin$ Share not reachable - not local admin - not domain admin - reachable in Explor

≪ Previous: Servidores proliant Ml110G9

$

0

0

I have an HP Proliant ML110 G7 server running with only 2Gb RAM installed. The RAM presently in the system is Samsung 2GB PC3-10600E i want to upgrade to 8 Gb, i 've just bought exactly the same RAM as is already installed however when i insert the new modules, the server beep and doesn't start!!!

I' ve tested the single ram and it's ok....but when i try to install more than one module...the server doesn't start!

(obviouslyrespecting thepopulatinglist)

I've already updated the bios of server to the latest realese....

Please could anyone offer advice as to what i could try next?

Thank you

Fabio

---

HP SUM 7.5.1 - Admin$ Share not reachable - not local admin - not domain admin - reachable in Explor

August 16, 2016, 5:54 am

≫ Next: HP Smarty Array difference between CISSS3 and SATA / SAS Driver

≪ Previous: memory upgrade problem ml110 g7

$

0

0

Hello,

i'm trying to use HP SUM to update all my Proliants.

I already used it for local installation but now i want to do the same remote. But i cannot access the admin$ share (the software says so, it is not true).

I used higher priviledged accounts. I executed HP SUM as admin. -> no change

I tried to access it from the system where HP SUM is installed with the windows explorer -> works like a charm

Found the solution to upgrade to the newest version (was using 7.4 before). Did not work either.

Can anyone help me with this?

Best regards

Stephan

HP Smarty Array difference between CISSS3 and SATA / SAS Driver

August 16, 2016, 6:38 am

≫ Next: consumer SSDs in ML 350 G6 with smart array p410i controller

≪ Previous: HP SUM 7.5.1 - Admin$ Share not reachable - not local admin - not domain admin - reachable in Explor

$

0

0

Hello Guy's,

hello Guy's, can somebody explaind the differences between these drivers Version ?

 

regards

Stefan

consumer SSDs in ML 350 G6 with smart array p410i controller

August 16, 2016, 7:33 am

≫ Next: DL380 Gen9 win server 2008 R2 Stuck shutdown screem

≪ Previous: HP Smarty Array difference between CISSS3 and SATA / SAS Driver

$

0

0

I am only using the HP ProLiant ML350 G6 servers with smart array p410i controllers in a development environment, but I would like to get the speed of enterprise SSD, without spending the $, as this is not going to ever have even a fraction of the workload of the production environment.

Forget that the solution is not optimal, are there any technical barriers prohibiting me from installing consumer grade SSD drives into the drive carriers and using them in the hot swap drive bays in the front of each server?

I accept that I will probably burn through the individual drives at a more rapid pace, but don't want to bother if there is no way to even get this functioning.

Any advice, suggestions, or documentation are appreciated.

Thanks,

Ed

DL380 Gen9 win server 2008 R2 Stuck shutdown screem

August 16, 2016, 10:04 am

≫ Next: adding independent drives to server without adding to the Raid Array

≪ Previous: consumer SSDs in ML 350 G6 with smart array p410i controller

$

0

0

Hi

I am Muhammad I just bought new server DL380 Gen9 already windows server 2012 (no licensed) installed, worked well. After installed win server 2008 R2 licensed it restarts normally, but while I shut down, the screen stay in stuck shutdown and health led of the server red blinking. The server stay, nothing changes the only way I have to press power button for a few seconds. Please tell me a solution 

Thanks

 

 

adding independent drives to server without adding to the Raid Array

August 16, 2016, 1:01 pm

≫ Next: Firmware Upgrade | G7 Servers

≪ Previous: DL380 Gen9 win server 2008 R2 Stuck shutdown screem

$

0

0

I have a DL180 G6 server with a P140 Smart array controller. I would like to add a couple of drives for storage without adding them to the raid array. I have tried to add them to the server by simply plugging them in the server does not see them. Do i need to preformate them befor installing them? Is it even possible to add the drives?

Firmware Upgrade | G7 Servers

August 16, 2016, 8:20 pm

≫ Next: DL380 Gen9 win server 2008 R2 Stuck shutdown screen

≪ Previous: adding independent drives to server without adding to the Raid Array

$

0

0

Hello,

Need info on upgrade versions available for following infrastructure - 

Host - ProLiant BL685c G7 

ESX Version installed on them. Esxi 5.0.0 191865

Current OA FW Version 3.32 Aug 24 201

Current VC FW Version  3.18

 

Please verify if my understanding is correct - 

VC version available for G7 servers is max 4.45 ? 

OA version available for G7 servers is max 4.50 ? 

What is the process to upgrade everything ? Sequence of upgrade ? 

DL380 Gen9 win server 2008 R2 Stuck shutdown screen

August 17, 2016, 1:53 am

≫ Next: Removing DL380 g6 and g7 from rack.

≪ Previous: Firmware Upgrade | G7 Servers

$

0

0

Hi

I am Muhammad I just bought new server DL380 Gen9 already windows server 2012 (no licensed) installed, worked well. After installed win server 2008 R2 licensed it restarts normally, but while I shut down, the screen stay in stuck shutdown and health led of the server red blinking. The server stay, nothing changes the only way I have to press power button for a few seconds. Please tell me a solution 

Thanks

 

 

---

Removing DL380 g6 and g7 from rack.

August 16, 2016, 8:38 pm

≫ Next: ProLiant DL380p G8 - Powering (and fitting) a Quadro K6000 card

≪ Previous: DL380 Gen9 win server 2008 R2 Stuck shutdown screen

$

0

0

I don't know where the rail kit instructions got off to, or if the instructions were provided with either server, which we bought refurbished. I can't see any markings or indications or features on the rails that would indicate how to get the server to slide out past the first stop at about 12-3/8 inches or how to release it from the rails. The rail kit of the g7 is product number 616992-001. I've searched high and low and found no usable help. The g6 looks the same as the g7, so I guess the product number for that rail kit will be similar, if not identical.

Any tips would be greatly appreciated.

ProLiant DL380p G8 - Powering (and fitting) a Quadro K6000 card

August 17, 2016, 10:09 am

≫ Next: HP RX2660 Monitoring

≪ Previous: Removing DL380 g6 and g7 from rack.

$

0

0

Trying to find the parts needed to power and fit for an NVidia Quadro K6000 grphx card into our server - ProLiant DL380p G8. Have the standard pci riser board, but the card will not fit into the pci x16 slot due to it being double height and the x16 is top slot and clearance issues. We are also trying to find the cables needed to power the card, it has 2 6-pin connections it needs. We've got 2 750w psu's, but I'm not sure how to tap into them.

Any help is greatly appreciated.

Thank you.

HP RX2660 Monitoring

August 17, 2016, 10:38 am

≫ Next: hp SUM issues

≪ Previous: ProLiant DL380p G8 - Powering (and fitting) a Quadro K6000 card

$

0

0

Hi,

How can I monitor a HP RX2660 to get CPU Temperature and other ?

Normally I have to use the iLO2 MP LAN port, no ? I can't access at 127.0.0.1 (connection refused). 

If it's possible, I would like to use Nagios and SNMP protocol but I don't have the MIB file. 

Thanks for your support,

Jerome

hp SUM issues

August 17, 2016, 10:56 am

≫ Next: RAID configuration for ProLiant DL380p Gen8

≪ Previous: HP RX2660 Monitoring

$

0

0

I managed to create a custom image to include the HP SUM, after FINALLY getting it to boot up, it ran once, created a baseline and now it just hangs.  Yes, I made sure the components added were for my server.  So what the hell?  Can someone please tell me how to get my server updated.  No I do not have an OS installed, No, I can't connect to ANYTHING, nor can I connect ANYTHING to my server. All I can do is use bootable DVDs. 

 

this is the worst process, I have ever encountered in my 17 years as an admin.  HP doesn't take in to consideration, that there just might be environments, that ABSOLUTELY can not connect to ANYTHING!  So why not just bring the **bleep** CDs back.  or make them easily manageable.   No, I can't use Dual layer DVDs, so yes, I have to be sure it fits on a regular DVD...NO this isn't my company's policy, its DOD policy, mind you who HPE just happens to have a billion dollar contract with. 

 

HP GET YOUR LIFE TOGETHER!!!

RAID configuration for ProLiant DL380p Gen8

August 9, 2016, 7:57 am

≫ Next: Determine the installed version of the Power Capping Microcontroller Firmware

≪ Previous: hp SUM issues

$

0

0

Hi,

      I configured 8 disks as two raid.

     raid 1: disk 1 + disk2 + disk3(spare)

     raid 5: disk 4~ 8

Why I see three disks when I booted to linux livecd.

lsblk:

sda 8:0 0 256M 1 disk
`-sda1 8:1 0 251M 1 part /media/VID
sdb 8:16 0 279.4G 0 disk
sdc 8:32 0 1.1T 0 disk

 

Determine the installed version of the Power Capping Microcontroller Firmware

August 18, 2016, 6:48 am

≫ Next: p410 controller on dl120 g6

≪ Previous: RAID configuration for ProLiant DL380p Gen8

$

0

0

For my Gen9 DL360's, I want to install the "Advanced Power Capping Microcontroller Firmware" on servers that need it. (These servers run Windows, and I would install cp025309.exe.) I am trying to determine which servers need it, but I cannot seem to programatically determine what version of that firmware a server has installed. I have searched through every WMI class in root\hpq (where I typically find firmware versions) and cannot find it anywhere.

Can someone point me to a registry location, file, WMI class, even HP utility output that can tell me what version of that firmware I have installed?

Thanks,
Eric

p410 controller on dl120 g6

August 18, 2016, 12:51 pm

≫ Next: DL580 G7 Processor Blank

≪ Previous: Determine the installed version of the Power Capping Microcontroller Firmware

$

0

0

Hello!

I've got trouble, I have HP DL120 G6 server with built-in b110i. I need to replace our 4x1Tb hard drives to 4x4Tb hard drives. For theese purposes I've bought P410 pci-e x8 controller, but bios doesn't recognize it, though on HP's download site there are drivers for p410 controller. 

How can I make it work?

---

DL580 G7 Processor Blank

August 18, 2016, 6:46 pm

≫ Next: Firmware Upgrade for OA + VC

≪ Previous: p410 controller on dl120 g6

$

0

0

I'm having a rough time finding a processor blank (plastic cover over the socket) for the DL580 G7 processors for shipping and using the server with only 2 CPUs. I'm sure they exist for the LGA 1567 socket... anyone happen to know a part number?

Firmware Upgrade for OA + VC

August 18, 2016, 9:18 pm

≫ Next: Smartstart Test vs Diagnostics

≪ Previous: DL580 G7 Processor Blank

$

0

0

Guys, 

A confirmation needed - both VC and OA and running with 3.70 (with 460G7 Blades) ,and needs to be updated to 4.50. 

Couple of Questions - 

1.

Please confirm > As per compatibility table, VC running at 3.70 is compatible with OA running 4.50 - 

http://h20564.www2.hp.com/hpsc/doc/public/display?docId=mmr_kc-0100204-12

 

2.  If we schedule upgrade of VC later, and just concentrate on OA upgrade, is this sequence of upgrade good  ? 

3.60 > 4.11 > 4.23 > 4.30 > 4.40 > 4.50

 

 

Smartstart Test vs Diagnostics

August 19, 2016, 2:15 am

≫ Next: Problem with OA - Onbord Administrator 2.31 , Enclosure info - BladeSystem c3000 ?

≪ Previous: Firmware Upgrade for OA + VC

$

0

0

Hi everybody!

Does anybody have knowledge about different between Test and Diagnostics in HP smartstart disk?

I have DL360G7 with array controller P410i with two HDD sff 300GB RAID1.

There are no any error during and after test storage but I have error code F155 on diagnostics.

Why so?

Problem with OA - Onbord Administrator 2.31 , Enclosure info - BladeSystem c3000 ?

August 19, 2016, 2:25 am

≫ Next: opening the case of a ProLiant ML350Gen9 desktop server

≪ Previous: Smartstart Test vs Diagnostics

$

0

0

Hi guys,

I have got the same problem from 2 - 3 days with my Onbord Administrator (OA).

It's happened twice morning, when I come to work in our server room is too noisily. When I login in OA I seeing my blade servers with Critical errors : Management Processor :  Error - lost communication with ILO , and their fans spins on 98%.

The reboot it is not decision, but when I pull out OA module from the chassis and back it again, everything is OK

That from below is OA System Logs from when I have problem with my OA:

Aug 17 04:07:54 OA: Management Processor on Blade 1 appears unresponsive.
Aug 17 04:08:04 OA: Management Processor on Blade 2 appears unresponsive.
Aug 17 04:08:14 OA: Management Processor on Blade 3 appears unresponsive.
Aug 17 07:38:28 OA: Authentication failure for user admin from 192.168.11.203, requesting web service
Aug 17 07:38:46 OA: admin logged into the Onboard Administrator from 192.168.11.203
Aug 17 08:29:45 OA: Blade removed from bay 3
Aug 17 08:29:45 OA: Blade inserted in bay 3
Aug 17 08:29:45 OA: Blade in bay #3 status changed to OK
Aug 17 08:29:45 OA: Management Processor on Blade 3 appears unresponsive.
Aug 17 08:31:45 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 08:33:45 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 08:44:19 OA: Blade removed from bay 3
Aug 17 08:44:19 OA: Blade inserted in bay 3
Aug 17 08:44:19 OA: Blade in bay #3 status changed to OK
Aug 17 08:46:19 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 08:47:37 OA: Management Processor on Blade 3 appears unresponsive.
Aug 17 08:48:19 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 09:31:39 OA: Blade removed from bay 3
Aug 17 09:31:40 OA: Blade inserted in bay 4
Aug 17 09:31:40 OA: Blade in bay #4 status changed to OK
Aug 17 09:33:40 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 09:35:04 OA: Management Processor on Blade 4 appears unresponsive.
Aug 17 09:35:40 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 09:44:11 OA: Blade removed from bay 4
Aug 17 09:44:11 OA: Blade inserted in bay 4
Aug 17 09:44:11 OA: Blade in bay #4 status changed to OK
Aug 17 09:46:11 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 09:47:35 OA: Management Processor on Blade 4 appears unresponsive.
Aug 17 09:48:11 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 10:37:36 OA: PowerDelay server settings have been changed.
Aug 17 10:39:57 OA: Blade removed from bay 4
Aug 17 10:39:57 OA: Blade inserted in bay 4
Aug 17 10:39:57 OA: Blade in bay #4 status changed to OK
Aug 17 10:41:58 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 10:43:21 OA: Management Processor on Blade 4 appears unresponsive.
Aug 17 10:43:58 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 10:44:54 OA: PowerDelay server settings have been changed.
Aug 17 10:57:36 OA: Onboard Administrator is rebooting
Aug 17 10:58:16 Kernel: Network link is up at 100Mbps - Full Duplex
Aug 17 10:58:17 OA: Time zone changed to GMT+2
Aug 17 10:58:19 OA: LCD Status is: OK.
Aug 17 10:58:21 Enclosure-Link: Service started
Aug 17 10:58:22 OA: Onboard Administrator booted successfully
Aug 17 10:58:31 Enclosure-Link: Initial topology scan completed successfully
Aug 17 10:59:48 OA: admin logged into the Onboard Administrator from 192.168.11.203
Aug 17 11:00:32 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 11:01:24 OA: Management Processor on Blade 1 appears unresponsive.
Aug 17 11:01:30 OA: Management Processor on Blade 2 appears unresponsive.
Aug 17 11:01:42 OA: Management Processor on Blade 4 appears unresponsive.
Aug 17 11:02:56 OA: Blade removed from bay 4
Aug 17 11:03:13 OA: Blade inserted in bay 3
Aug 17 11:03:13 OA: Blade in bay #3 status changed to OK
Aug 17 11:04:56 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 11:06:31 OA: Management Processor on Blade 3 appears unresponsive.
Aug 17 11:06:56 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 11:12:51 Kernel: Network link is up at 100Mbps - Full Duplex
Aug 17 11:12:53 OA: Time zone changed to GMT+2
Aug 17 11:12:54 OA: Server Power Reduction Mode - Enabled
Aug 17 11:12:55 OA: LCD Status is: OK.
Aug 17 11:12:56 Enclosure-Link: Service started
Aug 17 11:12:58 OA: Onboard Administrator booted successfully
Aug 17 11:13:06 Enclosure-Link: Could not acquire bottom enclosure's UUID. Cannot set RUID.
Aug 17 11:13:06 Enclosure-Link: Initial topology scan completed successfully
Aug 17 11:13:08 OA: Blade 3 is reporting nominal health status.
Aug 17 11:13:08 OA: Blade in bay #3 status changed to OK
Aug 17 11:13:13 Enclosure-Link: RUID recovered: 09CZC9027XJ3
Aug 17 11:13:28 OA: Blade 1 is reporting nominal health status.
Aug 17 11:13:28 OA: Blade in bay #1 status changed to OK
Aug 17 11:13:32 OA: Blade 2 is reporting nominal health status.
Aug 17 11:13:32 OA: Blade in bay #2 status changed to OK
Aug 17 11:13:36 OA: Server Power Reduction - Deactivated
Aug 17 11:13:36 OA: Server Power Reduction Mode - Disabled
Aug 17 11:13:40 OA: Server blade in bay 3 has been powered on
Aug 17 11:13:40 OA: Blade 3 is properly cooled.
Aug 17 11:14:09 OA: Blade in bay #3 status changed to OK
Aug 17 11:14:25 OA: admin logged into the Onboard Administrator from 192.168.11.203
Aug 17 11:14:29 OA: Blade in bay #1 status changed to OK
Aug 17 11:14:33 OA: Blade in bay #2 status changed to OK
Aug 17 11:15:08 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 11:15:08 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 17 11:17:08 Alertmail: Failed to send AlertMail to kiro@elkabel.bg

Aug 18 15:35:48 Kernel: Network packet flooding detected.
Aug 18 15:35:50 Kernel: Network packet flooding detected.
Aug 18 15:35:55 Kernel: Network packet flooding detected.
Aug 18 15:36:02 Kernel: Network packet flooding detected.
Aug 18 20:28:34 OA: Management Processor on Blade 1 appears unresponsive.
Aug 18 20:28:44 OA: Management Processor on Blade 2 appears unresponsive.
Aug 18 20:28:54 OA: Management Processor on Blade 3 appears unresponsive.
Aug 19 07:43:16 OA: admin logged into the Onboard Administrator from 192.168.11.203
Aug 19 07:51:20 OA: Onboard Administrator is rebooting
Aug 19 07:52:00 Kernel: Network link is up at 100Mbps - Full Duplex
Aug 19 07:52:00 OA: Time zone changed to GMT+2
Aug 19 07:52:01 OA: LCD Status is: OK.
Aug 19 07:52:03 Enclosure-Link: Service started
Aug 19 07:52:04 OA: Onboard Administrator booted successfully
Aug 19 07:52:13 Enclosure-Link: Initial topology scan completed successfully
Aug 19 07:53:13 OA: admin logged into the Onboard Administrator from 192.168.11.203
Aug 19 07:54:14 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 19 07:55:07 OA: Management Processor on Blade 1 appears unresponsive.
Aug 19 07:55:13 OA: Management Processor on Blade 2 appears unresponsive.
Aug 19 07:55:19 OA: Management Processor on Blade 3 appears unresponsive.
Aug 19 08:15:31 Kernel: Network link is up at 100Mbps - Full Duplex
Aug 19 08:15:32 OA: Time zone changed to GMT+2
Aug 19 08:15:34 OA: Server Power Reduction Mode - Enabled
Aug 19 08:15:36 OA: LCD Status is: OK.
Aug 19 08:15:38 Enclosure-Link: Service started
Aug 19 08:15:41 OA: Onboard Administrator booted successfully
Aug 19 08:15:47 Enclosure-Link: Initial topology scan completed successfully
Aug 19 08:15:47 OA: admin logged into the Onboard Administrator from 192.168.11.203
Aug 19 08:16:10 OA: Blade 1 is reporting nominal health status.
Aug 19 08:16:10 OA: Blade in bay #1 status changed to OK
Aug 19 08:16:15 OA: Blade 2 is reporting nominal health status.
Aug 19 08:16:15 OA: Blade in bay #2 status changed to OK
Aug 19 08:16:16 OA: Server Power Reduction - Deactivated
Aug 19 08:16:16 OA: Server Power Reduction Mode - Disabled
Aug 19 08:16:20 OA: Blade 3 is reporting nominal health status.
Aug 19 08:16:20 OA: Blade in bay #3 status changed to OK
Aug 19 08:17:10 OA: Blade in bay #1 status changed to OK
Aug 19 08:17:15 OA: Blade in bay #2 status changed to OK
Aug 19 08:17:20 OA: Blade in bay #3 status changed to OK

Aug 19 08:17:48 Alertmail: Failed to send AlertMail to kiro@elkabel.bg
Aug 19 08:18:08 Alertmail: Failed to send AlertMail to kiro@elkabel.bg

If someone has experience with similar errors please let me share what have to done.

Thank you in advance

opening the case of a ProLiant ML350Gen9 desktop server

August 19, 2016, 3:16 am

≫ Next: HPE SIM

≪ Previous: Problem with OA - Onbord Administrator 2.31 , Enclosure info - BladeSystem c3000 ?

$

0

0

Could someone help me with opening the case? I have used the key to unlock, and there is a screwdriver slotted handle which doesn't seem to do anything. Help please!