Hello,
does anyone have issue with FlexFabric 10Gb 2port 534FLR-SFP on Ubuntu 18.04?
My setup is - two interfaces in lacp bond and mtu 6000 .
The problem is that my servers are crashing with:
An Unrecoverable System Error (NMI) has occurred (Service Information: 0x00000000, 0xE0FF0000)
ASR Detected by System ROM
PCI Bus Error (Slot 0, Bus 0, Device 2, Function 2)
That is happening on three servers (DL380 Gen9) with similar hardware/firmware/settings.
They are with the latest SP and unfortunately, warranty has expired.
↧
Issue with HP FlexFabric 10Gb 2port 534FLR-SFP
↧
HP DL380pG8 E5-2609 Latest Drivers and Bios Utility
Hi All,
I am looking for "HP DL380pG8 E5-2609" server's utilities to check Windows Server 2012 r2 drivers updates and Bios updates.
The server is out of warranty and has no contract support with HPE.
Thanks in well Adv.
Best Regards
Faisal
↧
↧
B140i RAID5 write @ 80 MBs read @ 500 MBs
Just wanted to ask what peoples experience are with these base model ML30G9 with a B140i embedded controller using 4x MB001000GWFWK 1TB SATA drives in RAID5?
- I have enabled/disabled write cache and it does not make any difference
- I have enabled/disabled controller caching - no difference
- Tried different drivers 62.6.0.64, 62.8.0.64 and 62.12.0.64
According to ATTO, the highest write is 80 MB/s (Megabytes p/s) from 4MB although read is fantastic at 450 MBs+ at 4KB.
Any help would be much apprecaited.
I have logged a case and was advised it was write cache and waiting for further reply.
↧
HP ML150 Gen9 SSD on sata port on Motherboard
Hi,
I have a new HP ML150 Gen9 Tower, with dual 1TB SATA connected to the b140 storage controller. Using them in raid 0. Windows 2016 installed and everything runs perfect.
Now i decided to connect a loose SSD harddrive to a free sata connecter on the motherboard. The problem is that windows does not recognize the disk at all. Not te be found in device manager or anywhere else.
If i temporarily switch the bios from UEFI to Legacy i can see the drive in de boot options screen. So the drive seems te be properly recognized by the server. I also tested the ssd in a client pc and it works properly.
Can anyone give me advise in this matter?
Thx!
Dave
↧
system management homepage no items impossible d'installer HPE Insight Management WBEM Providers
la page affiche "no items" pour regler le probleme il indique d'installer les elemment suivant :
HPE Insight Management WBEM Providers and/or HPE Insight management Agents
mais il est impossible de les installer, je suis sous windows serve 2016
↧
↧
DL380 Gen 10 SAS HDD installation
Hello I have a DL380 Gen10 Server and I installed 2 SAS 10K HDD P/N 872477-B21. With intelligent provisioning the system can not see any disk do I have to set up anything to make them visible, the SR100S is enabled, the disks lights up but the system tells me that no disks are installed....any suggestions?
The P/N on the HPE box is 872477-B21 but on the HDD is written another P/N 876938-001
↧
Raid hard disks don't blink!
I have a server hp proliant dl180 g6, the raid keeps drops every few hours, i find the leds of all disks turned off.
↧
Replace disks in a RAID 1
Hello good afternoon.
I currently have a HPE ML110 G9 server with a 4GB p440 controller and the integrated b140 controller, in which I have the WS 2016 operating system in RAID 1. Currently in RAID 1 I have two 120GB OCZ TR150 disks with 20,000 working hours, and I would like to replace the two.
What would be the best system to replace the discs?
1 .- I make a backup of the operating system (I have backups made by Windows), change the disks and and reinstall the operating system of the backup? (I dont like this system very much).
2.- Replace a disk, let the system rebuild the new unit, and then replace the other and let it rebuild again.
The new discs that I want to incorporate are two Samsung 860 Pro 250GB, which have a larger size than the old OCZ. Once the two new 250GB disks are incorporated, will I be able to expand the total capacity from the SSA?
Thank you!
↧
ML350 G6 Server: Error reading power values from microcontroller
Just wanted to ask for help in following issue:
HP ML350 G6 server with redundant power supply, 750W each no errors during boot or in IML logs have error in the iLO2 interface related to power:
Error reading power values from microcontroller. No valid data can be gathered
Unable to communicate with power microcontroller
Server is updated to all current firmware and othervise runs OK, with only one issue: restarts itself after shutdown. (BIOS is set to: NOT RESTART AFTER SHUTDOWN)
System ROM: D22 (05/21/2018)
iLO2 Firmware: V2.33 (03/20/2018) Advanced version
RAM installed: 144GB 1333mhz (6 x 8GB + 6 x 16GB)
As reccomended in few old posts, server was shut down compleately, disconnected from power and restarted in 20 min, did not resolved the issue.
Any help would be much apprecaited.
↧
↧
Third-Party Software Update Catalogs in SCCM not able to download/Publish
Hi!
(Might be posted in the wrong location)
I'm a config manager (SCCM) administrator, and in the latest release of SCCM 1806, they have included a feature called "Third-Party Software Update Catalogs" which basically means WSUS can handle third-party updates.
I am however having some issues with 1 out of 4 updates from the HPE catalog?!
I'm suspecting the bold-marked link below to be wrong. It is atleast not the same link when I Published/downloaded the other updates
[34, PID:8952][10/03/2018 14:15:57] :PollingWorkMonitor: There are 1 jobs that are pending the jobs table.
[34, PID:8952][10/03/2018 14:15:57] :PollingWorkMonitor: Starting job 72057594037927950 for subject 5ccaf2ef-9fb4-4e85-8c34-cf04c07ef849.
[34, PID:8952][10/03/2018 14:15:57] :Creating a new SyncUpdate work item for update 5ccaf2ef-9fb4-4e85-8c34-cf04c07ef849, jobid is 72057594037927950
[56, PID:8952][10/03/2018 14:15:57] :SyncUpdate: 'HPE ProLiant Server Firmware 2018.06.0 (Update:'5ccaf2ef-9fb4-4e85-8c34-cf04c07ef849' Vendor:'HPE ProLiant Updates' Product:'Firmware Bundles')' is synchronized to WSUS without content, revision to add content is required.
[56, PID:8952][10/03/2018 14:15:57] :SyncUpdate: Checking if certificate is registered for server %ServerName%
[56, PID:8952][10/03/2018 14:15:57] :SyncUpdate: 5ccaf2ef-9fb4-4e85-8c34-cf04c07ef849 - Downloading file: 'http://updatespublisherlocalsourcepublishedsoftwareupdate/' to 'D:\ConfigMgr\ISVTemp\zpkimj12.vlr'.
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: An unexpected error ocurred attempting to download content from 'http://updatespublisherlocalsourcepublishedsoftwareupdate/':
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: ==================== Exception Detail Start =======================
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: Exception type: WebException
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: Exception HRESULT: -2146233079
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: Exception Message: An exception occurred during a WebClient request.
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: Exception source mscorlib
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: Exception TargetSite Void ThrowForNonSuccess(System.Threading.Tasks.Task)
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: Stack at System.Runtime.CompilerServices.TaskAwaiter.ThrowForNonSuccess(Task task)
at System.Runtime.CompilerServices.TaskAwaiter.HandleNonSuccessAndDebuggerNotification(Task task)
at Microsoft.ConfigurationManager.ISVUpdatesSyncAgent.DownloadManager.Request.<DownloadFileAsync>d__24.MoveNext()
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: ===================== Exception Detail End ========================
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: WebException status : 'UnknownError
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: 5ccaf2ef-9fb4-4e85-8c34-cf04c07ef849 - Download of update 5ccaf2ef-9fb4-4e85-8c34-cf04c07ef849 failed, unable to continue
[34, PID:8952][10/03/2018 14:15:57] :STATMSG: (SRVMSG_SMS_ISVUPDATES_SYNCAGENT_UPDATECONTENT_DOWNLOAD_FAIL).
[34, PID:8952][10/03/2018 14:15:57] :STATMSG: (SRVMSG_SMS_ISVUPDATES_SYNCAGENT_UPDATECONTENT_FAIL).
[34, PID:8952][10/03/2018 14:15:57] :SyncUpdate: 5ccaf2ef-9fb4-4e85-8c34-cf04c07ef849 - Completed.
The custom catalog settings are listed here:
And this is the remaining updates which are downloaded/published fine: (exept the first one which is my issue)
Hope someone can help me :)
Best Regards
Christian
↧
Find the latest firmware downloads for your Storage Disk Enclosures
Quickly locate your Storage Disk Enclosure model and check to see that you are running the current I/O module firmware --
Visit the HPE Storage Disk Enclosure - I/O Module Firmware reference page for information on the D6020, D6000, D3600/D3700/D3610/D3710, D2600/D2700 models.
- Vajith
↧
AlertMail with PowerShell
How does one use PowerShell to set the AlertMail "Enable SMTP Secure Connection (SSL/TLS)" option on a Gen10. I dont see any parameter to set this with the "Set-HPEiLOAlertMailSetting" cmdlet in the latest PowerShell module for iLO.
Thanks
NK
↧
Problem with a Raid 1+0 array on a Proliant DL380 G7 - Smart Array 410i
We have a DL380 had system board failure. Specifically, the disk controller. Took a couple trips, but they got the machine back up and running. However, there is a problem with a RAID 1+0 array on the server.
The file system on this Raid is up and apparently fine. Running RedHat.
The problem is that the array thinks it has 3 failed disks, and the controller thinks there are 3 spare disks.
array B (SAS, Unused Space: 0 MB)
logicaldrive 2 (1.6 TB, RAID 1+0, Interim Recovery Mode)
physicaldrive 1:5 (box 1:bay 5, SAS, 0 MB, Failed)
physicaldrive 1:7 (box 1:bay 7, SAS, 0 MB, Failed)
physicaldrive 1:8 (box 1:bay 8, SAS, 0 MB, Failed)
physicaldrive 2C:2:7 (port 2C:box 2:bay 7, SAS, 300 GB, OK)
physicaldrive 2C:2:8 (port 2C:box 2:bay 8, SAS, 300 GB, OK)
physicaldrive 3C:2:2 (port 3C:box 2:bay 2, SAS, 300 GB, OK)
physicaldrive 3C:2:3 (port 3C:box 2:bay 3, SAS, 300 GB, OK)
physicaldrive 3C:2:4 (port 3C:box 2:bay 4, SAS, 300 GB, OK)
physicaldrive 4C:1:1 (port 4C:box 1:bay 1, SAS, 300 GB, OK)
physicaldrive 4C:1:2 (port 4C:box 1:bay 2, SAS, 300 GB, OK)
physicaldrive 4C:1:3 (port 4C:box 1:bay 3, SAS, 300 GB, OK)
physicaldrive 4C:1:4 (port 4C:box 1:bay 4, SAS, 300 GB, OK)
physicaldrive 5C:1:6 (port 5C:box 1:bay 6, SAS, 300 GB, OK, active spare)
unassigned
physicaldrive 5C:1:5 (port 5C:box 1:bay 5, SAS, 300 GB, OK)
physicaldrive 5C:1:7 (port 5C:box 1:bay 7, SAS, 300 GB, OK)
physicaldrive 5C:1:8 (port 5C:box 1:bay 8, SAS, 300 GB, OK)
Doesn't take long to see that there is a house keeping issue here.
We tried reseating one of the drives to see if that would get the controller to figure it out, but that didn't happen.
My next thought is that we could go in hpacucli and remove the "failed" disks and add in the spares.
- Ctrl slot=0 array B remove drives=1:5,1:7,1:8
- Ctrl slot=0 array B add spares=5C:1:5,5C:1:7,5C:1:8
Then, I'm not sure what command to use to get the spares to take over and be full members of the array and not just spares.
Is there any danger to this? If we have to, we can delete the disk and array, and rebuild them, but we already had a week long outage due to the failure, and would rather keep the machine up.
Any help would be appreciated?
thanks,.
Paul.
↧
↧
Error creating cache SSD for raid5 array
Hello all.
I have a ProLiant DL380 G6 with a Smart Array P410i. There is a need to create a disk cache for Logical Drive
ctrl all show config detail:
Smart Array P410i in Slot 0 (Embedded)
Bus Interface: PCI
Slot: 0
Serial Number: 50123456789ABCDE
Cache Serial Number: PAAVP9SYA66L
RAID 6 (ADG) Status: Disabled
Controller Status: OK
Hardware Revision: C
Firmware Version: 2.74
Rebuild Priority: High
Expand Priority: Medium
Surface Scan Delay: 15 secs
Surface Scan Mode: Idle
Queue Depth: Automatic
Monitor and Performance Delay: 60 min
Elevator Sort: Enabled
Degraded Performance Optimization: Disabled
Inconsistency Repair Policy: Disabled
Wait for Cache Room: Disabled
Surface Analysis Inconsistency Notification: Disabled
Post Prompt Timeout: 0 secs
Cache Board Present: True
Cache Status: OK
Cache Ratio: 0% Read / 100% Write
Drive Write Cache: Enabled
Total Cache Size: 512 MB
Total Cache Memory Available: 400 MB
No-Battery Write Cache: Enabled
Cache Backup Power Source: Batteries
Battery/Capacitor Count: 1
Battery/Capacitor Status: OK
SATA NCQ Supported: True
Array: A
Interface Type: SAS
Unused Space: 0 MB
Status: OK
Array Type: Data
Logical Drive: 1
Size: 820.2 GB
Fault Tolerance: 1+0
Heads: 255
Sectors Per Track: 32
Cylinders: 65535
Strip Size: 128 KB
Full Stripe Size: 768 KB
Status: OK
Caching: Enabled
Unique Identifier: 600508B1001037383941424344451700
Disk Name: /dev/sda
Mount Points: None
Logical Drive Label: A013004550123456789ABCDEA520
Mirror Group 0:
physicaldrive 2C:1:4 (port 2C:box 1:bay 4, SAS, 146 GB, OK)
physicaldrive 2C:1:3 (port 2C:box 1:bay 3, SAS, 146 GB, OK)
physicaldrive 2C:1:2 (port 2C:box 1:bay 2, SAS, 146 GB, OK)
physicaldrive 2C:1:1 (port 2C:box 1:bay 1, SAS, 146 GB, OK)
physicaldrive 3C:1:8 (port 3C:box 1:bay 8, SAS, 146 GB, OK)
physicaldrive 3C:1:7 (port 3C:box 1:bay 7, SAS, 146 GB, OK)
Mirror Group 1:
physicaldrive 3C:1:6 (port 3C:box 1:bay 6, SAS, 146 GB, OK)
physicaldrive 3C:1:5 (port 3C:box 1:bay 5, SAS, 146 GB, OK)
physicaldrive 4C:2:4 (port 4C:box 2:bay 4, SAS, 146 GB, OK)
physicaldrive 4C:2:3 (port 4C:box 2:bay 3, SAS, 146 GB, OK)
physicaldrive 4C:2:2 (port 4C:box 2:bay 2, SAS, 146 GB, OK)
physicaldrive 4C:2:1 (port 4C:box 2:bay 1, SAS, 146 GB, OK)
Drive Type: Data
physicaldrive 2C:1:1
Port: 2C
Box: 1
Bay: 1
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD5
Serial Number: BS05P890ESUW0838
Model: HP DG146BABCF
Current Temperature (C): 33
Maximum Temperature (C): 53
PHY Count: 2
PHY Transfer Rate: 3.0Gbps, Unknown
physicaldrive 2C:1:2
Port: 2C
Box: 1
Bay: 2
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD7
Serial Number: 3NM3YNN900009819U07U
Model: HP DG146ABAB4
Current Temperature (C): 30
Maximum Temperature (C): 50
PHY Count: 1
PHY Transfer Rate: 3.0Gbps
physicaldrive 2C:1:3
Port: 2C
Box: 1
Bay: 3
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPDE
Serial Number: 6SD3CAWK0000B142LPPC
Model: HP EG0146FAWHU
Current Temperature (C): 29
Maximum Temperature (C): 49
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 2C:1:4
Port: 2C
Box: 1
Bay: 4
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD7
Serial Number: 3NM3TB5R00009752Y4E9
Model: HP DG146ABAB4
Current Temperature (C): 31
Maximum Temperature (C): 48
PHY Count: 1
PHY Transfer Rate: 3.0Gbps
physicaldrive 3C:1:5
Port: 3C
Box: 1
Bay: 5
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD5
Serial Number: PCWUUMME
Model: HP DG0146FARVU
Current Temperature (C): 28
Maximum Temperature (C): 39
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 3C:1:6
Port: 3C
Box: 1
Bay: 6
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD5
Serial Number: PCWWU1BE
Model: HP DG0146FARVU
Current Temperature (C): 28
Maximum Temperature (C): 39
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 3C:1:7
Port: 3C
Box: 1
Bay: 7
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD5
Serial Number: PCWWTGRE
Model: HP DG0146FARVU
Current Temperature (C): 29
Maximum Temperature (C): 39
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 3C:1:8
Port: 3C
Box: 1
Bay: 8
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD5
Serial Number: PCWWVPSE
Model: HP DG0146FARVU
Current Temperature (C): 31
Maximum Temperature (C): 40
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 4C:2:1
Port: 4C
Box: 2
Bay: 1
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 15000
Firmware Revision: HPDG
Serial Number: 6TB2A1970000B2033UNS
Model: HP EH0146FAWJB
Current Temperature (C): 29
Maximum Temperature (C): 40
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 4C:2:2
Port: 4C
Box: 2
Bay: 2
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 15000
Firmware Revision: HPDC
Serial Number: 3TB0JX6K00009010V8W8
Model: HP DH0146FAQRE
Current Temperature (C): 31
Maximum Temperature (C): 60
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 4C:2:3
Port: 4C
Box: 2
Bay: 3
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 15000
Firmware Revision: HPDD
Serial Number: 3TB143PT00009027TW0D
Model: HP EH0146FAWJB
Current Temperature (C): 31
Maximum Temperature (C): 59
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 4C:2:4
Port: 4C
Box: 2
Bay: 4
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 15000
Firmware Revision: HPDC
Serial Number: 3TB0KQJZ00009011WUYF
Model: HP DH0146FAQRE
Current Temperature (C): 32
Maximum Temperature (C): 60
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
Array: B
Interface Type: SAS
Unused Space: 0 MB
Status: OK
Array Type: Data
Logical Drive: 2
Size: 558.7 GB
Fault Tolerance: 5
Heads: 255
Sectors Per Track: 32
Cylinders: 65535
Strip Size: 256 KB
Full Stripe Size: 512 KB
Status: OK
Caching: Enabled
Parity Initialization Status: In Progress
Parity Initialization Progress: 4.11% complete
Unique Identifier: 600508B1001037383941424344451E00
Disk Name: /dev/sdb
Mount Points: None
Logical Drive Label: AD218B2950123456789ABCDE8CEC
Drive Type: Data
physicaldrive 5C:2:6
Port: 5C
Box: 2
Bay: 6
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 300 GB
Rotational Speed: 15000
Firmware Revision: 0005
Serial Number: 6XN2QE540000B324H25H
Model: SEAGATE ST9300653SS
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 5C:2:7
Port: 5C
Box: 2
Bay: 7
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 300 GB
Rotational Speed: 15000
Firmware Revision: 0005
Serial Number: 6XN2CJEE0000B317C8TB
Model: SEAGATE ST9300653SS
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
physicaldrive 5C:2:8
Port: 5C
Box: 2
Bay: 8
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 300 GB
Rotational Speed: 15000
Firmware Revision: 0005
Serial Number: 6XN766630000M503VXSK
Model: SEAGATE ST9300653SS
PHY Count: 2
PHY Transfer Rate: 6.0Gbps, Unknown
unassigned
physicaldrive 5C:2:5
Port: 5C
Box: 2
Bay: 5
Status: OK
Drive Type: Unassigned Drive
Interface Type: Solid State SATA
Size: 480.1 GB
Firmware Revision: CS131122
Serial Number: PNY09162169920311C89
Model: ATA PNY CS1311 480GB
SATA NCQ Capable: True
SATA NCQ Enabled: True
SSD Smart Trip Wearout: Not Supported
PHY Count: 1
PHY Transfer Rate: 3.0Gbps
Enclosure SEP (Vendor ID HP, Model HP SAS EXP Card) 248
Device Number: 248
Firmware Version: 1.52
WWID: 50014380065CE765
Box: 2
Vendor ID: HP
Model: HP SAS EXP Card
Expander 250
Device Number: 250
Firmware Version: 1.52
WWID: 50014380065CE766
Box: 1
Vendor ID: HP
SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 249
Device Number: 249
Firmware Version: RevC
WWID: 50123456789ABCED
Vendor ID: PMCSIERA
Model: SRC 8x6G
=>
but when I try to create ldcache I get the following error:
=> ctrl slot=0 create type=ldcache drives=5C:2:5 datald=2
Error: This operation is not supported with the current configuration. Use the
"show" command on devices to show additional details about the
configuration.
Reason: Not supported
What am I doing wrong?
Are there any other restrictions besides the ldcaсhe array?
↧
Redhat linux OS installation
i need to install redhat linux 6.0 on DL 380 gen 10 server , so is it possible.?
↧
Have an ML350 gen10 with e208i-a controller, Can I also use the onboard SATA controller?
I want to add a LFF drive cage to my ML350 gen10 with an e208i-a controller that already has 8 sff. Is there a way to use the onboard sata controller for the LFF drives? If not, how can I make it work? buy another sata controller? Any recommendations? I don't need hardware raid for the sata drives.
↧
How to add a sound card to Proliant DL380 G7
Hi
I have a one question about ,"How can i install The sound card on the server Proliant DL380G7"
I installed the ESXI 6.0 on this server and now i need a sound card , can you guid me how can i use sound adaptor ?
thanks
↧
↧
I can't access to intelligent provisioning via F10.
as in the object I can't access to intelligent provisioning via F10 , on ML350 GEN10
As suggested in other posts, I installed the Intelligent Provisioning Recovery Media for Gen10 v. 3.20 but the problem persists.
I can't access to intelligent provisioning via System Utilities.
I can access to intelligent provisioning via Ilo. Here we can the see the wizard for the first configuration. I can run the wizard until the end, and arrive to see in the browser a a screen with teh following message : "Intelligent provisioning api is not registered yet.please wait while the server is booting to itelligent provisioning.....". meanwhile the server switches off and on automatically and goes to the home screen with only the F10 button visible and active: but the intelligent repository doesn't start.
What can I do ?
Thanks
Andrea
↧
HPE Smart Array P816i-a SR Gen10 changing box number
Hi All,
I have 4 DL380 Gen10 servers with "HPE Smart Array P816i-a SR Gen10"
On 3 servers I have "Internal Drive Cage at Port 3I, Box 3, OK", on the 4th I have "Internal Drive Cage at Port 3I, Box 8, OK",
so my disk are named
3I:8:1 (SAS HDD, 4.7 TB), 3I:8:2 (SAS HDD, 4.7 TB), 3I:8:3 (SAS HDD, 4.7 TB), 3I:8:4 (SAS HDD, 4.7 TB)
instead of
3I:3:1 (SAS HDD, 4.7 TB), 3I:3:2 (SAS HDD, 4.7 TB), 3I:3:3 (SAS HDD, 4.7 TB), 3I:3:4 (SAS HDD, 4.7 TB)
Is there any ways to rename box 8 in box 3?
Thanks
↧
HP Insight Foundation Agents Properties
H90 DL380, Window 2008 r2.
Not able to start the service of HP Insight Foundation Agents in manual and Automatic.
Message :
Winodws could not start the HP Insight Foundation Agents service on Local Computer.
Error : 1608 : The dependency service or group failed to start.
↧