I have 22 HPE DL380 Gen10 servers running vSphere 6.7
I upgraded vCenter to 6.7U3 and am now starting to upgrade the ESXi hosts to 6.7U3.
The first host I upgraded, I noticed in the ESXi event log many errors related to "Sensor -1" being logged every minute.
There was a new EP13 patch released by VMware to fix this, however even after applying this new patch, the Sensor -1 hardware error is still occuring.
Anyone else having this issue?
Server 2019 - standard GUI
Whats the best option here for nic teaming - Is the HP recomended software better or use intergrated windows software - through server 2019
ProLiant DL380 Gen10 - HPE Ethernet 1Gb 4-port 331i Adapter - NIC
Where do I get the HP teaming software for this adapter -
As per microsoft document what settings are people using - we are going with
LACP
Dynamic ? - I think
None all adapters Active
One of our servers, an HP ML350 G6 has broken down (motherboard problem).
We have another server, an HP ML310 G8 and I want to know if it would be possible to move the SAS disk from the old server (ML350 G6) to the new server (ML310 G8) and try to boot the new server.
It's is necesary to change something in the new server to allow this migration of disk? Or it's impossible?
We have 6 SAS disk configured in RAID 1 (two of them) and RAID 5 (the rest of disks).
Is compatible the ML310 G8 disk controller?
Thanks in advance,
Marcos.
Hi All,
I want to know something simple actually, but I can not find it out after searching on the internet.
I want to install Windows Server via Intelligent Provisioning. After RAID configuration, then we create one big logical drive with all size available on the RAID group.
Then I go to 'Install OS Express' to start installing OS. What I look for is how to limit C drive on OS? I do not want to use all logical drive with big size to be C drive all. I want to to use around 100 - 150 Gb only to be C drive, while the rest I will set to be DATA drive. But anyway, I can not find any form/feature to limit C drive on 'Install OS Express'. Maybe I miss it somewhere? Please share if you know how to get this purpose.
Best Regards,
Mantap27
hello guys im new on installing OS in HP Proliant ML350 G5 can any one help me how to install the OS thanks in advance
Goodmorning everyone,
I recently purchased a Proliant DL380 G7 for my home lab and I connected an SSD on which I installed ESXi 6.7.
I exported a 2TB volume from the NAS with NFS protocol to ESXi which sees it correctly.
The problems are:
1. ESXi detects an undefined error on the vmhba0 card (Smart Array P410i)
2. SSD is unusable (on datastore browser an error appears)
3. All the VMs running on the 2TB NFS datastore are terribly slow (CPU and RAM have nothing to do with it and the old server used the same NAS but was faster)
4. When I try to stop the server the red health led turns on and the machine does not turn off.
Can you kindly help me with these problems?
Thanks a lot!
Hello,
I have an hp dl380 g6 server.
After some time the server restarts itself.
Asr is off.
Got this error on one of the Servers, local AMC engineers suggested to replace the capacitor (SPS-CA CAPACITOR 36in FL)
1705-Slot X Drive Array - Please replace Cache Module Super-Cap. Caching will be enabled once Super-Cap has been replaced and charged.
is it the correct solution and if we replace will it lose any data
Hi
Is there a fast way to do it, SPP or similiar? Usually I have had problems utilizing HP's smart / intelligent methods. The firmware level is no apx. 5/2017.
HPE ProLiant DL380 Gen9 E5-2620v4 8-Core (1 CPU)
P/N: 843556-425
Smart Array P440ar/2G Module
No ILO license
Four Win Server 2012-2016 VMs
HPE 32GBmicroSDMainstream Flash Media Kit -SD for ESXi
VMware vSphere Essentials 6 Kit
Veeam Backup & Replication Std f.VMware
Hello
We have just replaced the battery in Smart array cache, but since then the cache is disabled:
# ssacli ctrl all show status
Smart Array P410i in Slot 0 (Embedded)
Controller Status: OK
Cache Status: Temporarily Disabled
Battery/Capacitor Status: OK
I tried to power off/on the server and iLO but it didn't help. Can I enable the cache by some command or is it some other error?
Thanks
Ondrej Vesely
Can someone explain to me why the Support Center page dedicated to Proliant MicroServers Gen10 contains a lot of downloads (manuals, drivers, etc) regarding iLO, if the Microserver Gen10 doesn't support iLO?
This is very deceiving. I have spent a lot of time trying to read about iLO, before discovering that this particular generation of the MicroServer does not support iLO.
Hallo,
hättet ihr bitte einen Tip für mich? Ein PL DL380 Gen9 soll eine 2080Ti Grafikkarte bekommen. Bisher nicht mein Thema... Ich bin im Zweifel hinsichtlich des Platzes / Bauform / Steckplatz.
Vielleicht hat ja jemand genau in dieser Paarung etwas bereits verbaut?
Vielen Dank vorab!
I would like to try to otpimize the cost of server-switch networking, as SFP28 trancivers are quite expensive. Active optical cabling seems as quite effective solution, but I can't find any article or document to confirm interoperatibility. Does anybody have experience with HPE Ethernet 10/25Gb adapters and Cisco active optical cables? I don't exepct any technical issue, but formally speaking there is no document where interoperability is confirmed officially.
I'm considering HPE Eth 10/25Gb 2P 640FLR-SFP28 Adptr (817749-B21) and Cisco SFP-25G-AOC (active optical cable).
Thanks, Bojan
have a ProLiant ML350p Gen8 that has firmware 2.55
Getting module cache failed, which firmware do i need to upgrade to exactly? i want to try that before getting replacement battery for cache.
HI,
I,m searching for these drive bays at the back of a 380 gen 10. However, i,m unable to find them. It seems they are nvme bays, and I would also like to put NVME, drives in them, but it,s a real puzzle to find out what the article numbers/ part numbers are and where you can order them.
Can anyone point me in the right direction ?
Hi all,
It is my first post, I would like to thank you for the contributions received in this forum.
I have a trouble with a HP ProLiant ML 350 G5. I defined a test boot password with 7 character, confirm it, reboot and it worked great.
Since it worked correctly, I reset the password by adding a bar at the end when entering it. It also worked correctly. When defining the final password, I used a password with 8 characters, but now when starting it does not recognize the password "invalid password". I tried the first 7 characters and it doesn't work.
Any suggestions? The server has an ilo 2. It is located in a remote location in the organization, so resetting the BIOS is a non-viable option.
Thank you very much in advance for your collaboration.
ML350G6 server. When powered on fans works loudly but there is no signal on screen, even standard proliant bios logo screen. After some time server seems to reset itself.
iLO works. Log shows multiple "Server reset." and "Server power restored." (bot not "Server power removed") messages.
When powered on first 4 led on motherboard lit green and last 2 blinking green. Leds on NICs are lit too
What could it be and how to get the server back to work?
We just acquired an HP DL380 Gen 9 with the 6-disk NVMe strorage bay. We don't have the money for official HP NVMe drives so we are using Intel P3500 drives. I'm testing out hot-swap capability but it appears that pulling a drive causes the system to crash. Tested with EL8.0 and EL7.7. From what I've read in various places it seems like this should work. What am I missing?
