Hello everyone,
Does anyone have any information on whether the following components can be installed in the DL 385 Gen10:
2 x Maxtor C680 graphic cards (requires full lenght slot) + capture card Maxtor Mura IPX (requires half lenght slot)
The default riser that comes with the server has two half lenght slots, and one full lenght slot.
BR
Hi .. im racking my head and cant find this error.
Have smartupdate installed on linux.
# smartupdate --s --target my.ip.addy --targettype oa --username user --password pass --use_location /var/tmp/spp --dryrun
Error: Cannot get a valid session. Please check whether the server is running.
Sending Shutdown request to engine
Shutdown post command failed: 2
Thank you
My machine has been configured with RPS Enablement Kit and two 750W Hot Plug Power, but the current power readings cannot be displayed in iLO, and the program reports that this platform is not supported when I try to update Advanced Power Capping Microcontroller Firmware
Brand new ML350 Gen10 server with Windows Server 2019 started to shutdown unexpectedly since a couple of weeks. It has done this three times now. Windows event logs don't show anything, even no 'previous shutdown was unexpected'.
So it looks like something is shutting the system down, for no apparent reason.
The ILO event log shows:
1736 Host REST logout: System Administrator, 05/05/2020 06:03:57, 17, Security, Administration
1735 Host REST login: System Administrator, 05/05/2020 06:03:52, 17, Security, Administration
1734 Server power restored., 05/05/2020 06:02:48, 1, Maintenance, Administration
1733 Server reset., 05/05/2020 06:02:48, 1, Maintenance, Administration
1732 Server power removed., 05/05/2020 05:16:49, 1, Maintenance, Administration
1731 Embedded Flash: Restarted, 05/05/2020 05:16:42, 1, Firmware
1730 Server reset., 05/05/2020 05:16:39, 1, Maintenance, Administration
This is around the time users reported the system to be down. The power button LED is orange then and the server has to be powered on.
The APC UPS event log only shows "Monitoring stopped" and "Monitoring started" around the shutdown/power on times.
The server is in a 19" rack and someone shutting it down can be ruled out.
Any indication where to search would be very helpfull.
hello All
Somme body help me to get HPE proliant DL360 Bios firmware. link to download it if possible.
thank advence
Hi HP,
Ethernet Bonding is not working with non-HP switch.
HP DL380 gen9 to non-HP switch.
1. Both ports indivdiually working fine. But when, one of the bonded ethernet port disabled secondary port not coming up (As we configure, Bonding Mode: fault-tolerance (active-backup))
2. Secondary interface MII Status is showing down, Only it comes UP, once config changed to Active-Active at switch end.
Please find the below mentioned output for reference and suggest.
===================MII Status: down==============================
cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eno1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eno2
MII Status: down
Speed: Unknown
Duplex: Unknown
Link Failure Count: 7
Permanent HW addr: xxxxxxxxxx2
Slave queue ID: 0
Slave Interface: eno1
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 1
Permanent HW addr: xxxxxxxxxx1
Slave queue ID: 0
================================================
==============MII Status: up==========================
cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eno1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eno2
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 6
Permanent HW addr: xxxxxxxxxx2
Slave queue ID: 0
Slave Interface: eno1
MII Status: up
Speed: 1000 Mbps
Duplex: full
Link Failure Count: 1
Permanent HW addr: xxxxxxxx1
Slave queue ID: 0
======================================
Some configs and output for reference. Is it any parameter missing in configuration at server side ?
$ ifconfig eno1
eno1: flags=6211<UP,BROADCAST,RUNNING,SLAVE,MULTICAST> mtu 1500
ether xxxxxxxxxxxx1 txqueuelen 1000 (Ethernet)
RX packets 505090 bytes 96640736 (92.1 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 468645 bytes 185166132 (176.5 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 16
---------------------------------------
$ ifconfig eno2
eno2: flags=6147<UP,BROADCAST,SLAVE,MULTICAST> mtu 1500
ether xxxxxxxxxxxx2 txqueuelen 1000 (Ethernet)
RX packets 2894 bytes 372821 (364.0 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1020 bytes 335840 (327.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 17
------------------------------------------
$ ifconfig bond0
bond0: flags=5187<UP,BROADCAST,RUNNING,MASTER,MULTICAST> mtu 1500
inet xxxxxxxx netmask xxxxxxxx broadcast xxxxxxxxx
inet6 xxxxxxxxxxxxxx prefixlen 64 scopeid 0x20<link>
ether 94:18:82:80:22:d0 txqueuelen 1000 (Ethernet)
RX packets 508026 bytes 97018703 (92.5 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 469696 bytes 185510046 (176.9 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
------------------------------------------------
cat ifcfg-bond0
DEVICE=bond0
NAME=bond0
TYPE=Bond
NM_CONTROLLED=no
BONDING_MASTER=yes
IPADDR=xxxxxxxxxxxx
PREFIX=28
GATEWAY=xxxxxxxxxxx
IPV6INIT=no
DEFROUTE=yes
ONBOOT=yes
BOOTPROTO=none
BONDING_OPTS="mode=active-backup miimon=100"
[network-scripts]$
------------------------------------------
[network-scripts]$ cat ifcfg-eno1
TYPE=Ethernet
BOOTPROTO=none
DEFROUTE=yes
NAME=eno1
UUID=xxxxxxxxxxxx
DEVICE=eno1
ONBOOT=yes
NM_CONTROLLED=no
MASTER=bond0
SLAVE=yes
--------------------------------------
[network-scripts]$ cat ifcfg-eno2
TYPE=Ethernet
BOOTPROTO=none
DEFROUTE=yes
NAME=eno2
UUID=xxxxxxxxxxxx
DEVICE=eno2
ONBOOT=yes
NM_CONTROLLED=no
MASTER=bond0
SLAVE=yes
=================================
Hi,
We are trying to run two graphics card on a DL380P Gen8 with 2x E5-2690v1 and 2x 1200W power supplies. We bought the 662525-001 PCI Risers as well as the molex adapters to plug the power into the card. For the graphics card, we bought 2x Nvidia Quadro M5000. The server is running Windows Server 2019.
We have encountered two problems.
First of all, the graphics card do not seem to be detected by the system. Plugging in a monitor will do nothing, during booting as well as when Windows is booted. Installing a driver is not possible, as the nvidia installer says it cannot detect a graphics card.
Second, we are only capable of installing the graphics card in the secondary riser slot. Installing the graphics card in the primary slot gives an error at boot that the riser is not compatible with the slot it was put in (the primary slot). If the problem is the PCI riser, is there any that are compatible with the primary slot that have space for a graphics card ?
Thank you very much
I can't seem to update the firmware on this gen10 server. It has a P816i-a so I downloaded the firmware here:
https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX-1b866626447b4d64b798e0a52a#tab-history
I followed the instuctions and it appears to flash the firmware fine:
# ./setup
Supplemental Update / Online ROM Flash Component for Linux (x64) - HPE Smart Array P408i-p, P408e-p, P408i-a, P408i-c, E208i-p, E208e-p, E208i-c, E208i-a, P408i-sb, P408e-m, P204i-c, P204i-b, P816i-a and P416ie-m SR Gen10 (2.65), searching...
1) HPE Smart Array P816i-a SR Gen10 in Slot 0 (1.99)
Select which devices to flash [#,#-#,(A)ll,(N)one]> 1
Flashing HPE Smart Array P816i-a SR Gen10 in Slot 0 [ 1.99 -> 2.65 ]
Deferred flashes will be performed on next system reboot
============ Summary ============
Smart Component Finished
Summary Messages
================
Reboot needed to activate 1 new FW image
Exit Status: 1
Deferred flashes will be performed on next system reboot
A reboot is required to complete update.
But when I reboot I get:
A controller failure event occurred prior to this power-up. (Previous lock up code = 0x14803) Action: Install the latest controller firmware. If the problem persists, replace the controller.
The controller appears to work in the System Provisioning menus, so I don't think it's dead... I can even flash it again, but it never boots.
Any ideas?
Hello everyone, recently I noticed a problem that I think is related to the hard disk ( I state that I have tested the HDD in other servers and does not present these problems) . I own a proliant ml350 g5 and in the smart array I put two hdd sas in raid 0 and a 2 tb sata hdd that is recognized perfectly by the os. By making network transfers via windows the maximum transfer speed is 100 mbps (I used cat5e cables), also the speed tends to decrease more and more quickly during the transfer and keeping at a maximum speed of 6mbps making the transfer very long and excruciating! It's strange this thing has never happened to me! I thank you for your help, hello guys
Hi. I got one hard drive failed in raid. After this, ive tried swapping working drive with failed (swapped bay 2 and bay
For now logical drive is not recognising anymore. I am getting error:
SLot 0 HP Smart Array P420i Controller
1785-Slot 0 Drive Array not configured
Drive Positions appear to have changed
Run Array Diagnostic Utility (ADU) if previous positions are unknown
Then turn system off and move drives to the original positions.
Is there any chance to rebuilt raid configuration to its initial state?
Hi,
I'm trying to setup ILO Federation for a couple of DL380Gen10 server. I did not change much on the iLO Federation page, I can't see any other devices. I created a new group, chose a key, and configured this group an 3 ILO's. But they just don't see each other. ILO configuration is IPv4. Do I have to add an IPv6 address for this to work? iLO's are in the same VLAN. I don't know for sure if IPv6 Multicast is enabled. Isn't there an option to add IPv4 addresse manually to get this to work?
Hi,
I have a HP ProLiant DL360p Gen8 server with OS Version "Windows Server 2008 R2". The server was rebooted unexpectedly. HP ProLiant Integrated Management Log (IML) Viewer contains the following error:
POST Error: 1770 - Slot X Drive Array - Disk Drive Firmware Update Rcommended
System log contains the following info:
05/03/2020 12:07:34 24687 4 Cissesrv SYSTEM A firmware update is needed for the physical drive with product ID EG0300FBDBR connected to array controller P420i [Embedded].
The recommended minimum firmware revision should be HPD7.
05/03/2020 12:07:02 6008 1 EventLog SYSTEM The previous system shutdown at 12:03:10 PM on ?5/?3/?2020 was unexpected.
05/03/2020 12:06:33 41 1 Microsoft-Windows-Kernel-Power SYSTEM The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.
The current Smart Array P420i in Slot 0 (Embedded) Firmware Version is v8.32. Could you please explain more about this post error 1770 and what can be done to avoid this error?
Regards,
Peggy
Hi, good afternoon.
I have this controller installed on an ML110 G9 with 8 x 10TB on RAID5. The controller has battery for the cache, and the free space in the set is 27TB of a total of 70TB or so.
Why don't I get the option to migrate to RAID6?
Thank you!
The idling CPU usage on a HPE Proliant ML110 Gen10 with Windows 2019 Server STD is at 5 to 8%, which is higher than my other Gen9 ML servers with windows 2012 R2 or 2016. Particularly the Services and controller app seem stuck in the 2 to 4% range. It is not very much, but still annoying and I would like to understand if this is normal and what this process actually does! I have not seen this process in any of my older Windows servers, but I may have missed it? This particular server has the first generation Xeon 3104 scalable processor, is mail server and is just recently configured with no particular problem during setup.
Any observations or experiance is appreciated!
Hello!
I was really excited to find the "Settings", "Monitoring", and "Workload Advisor" under Performance on my customer's DL380 Gen10 iLO5. However, when I looked at my second server, the "Settings" and "Workload Advisor" was missing. I found https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=emr_na-a00092978en_us which said to do an ILO reset and as long as you have the correct license you should see these two tabs. But that didn't work. And the Performance - Monitoring tab doesn't show any data (CPU Utilization, etc.). Something appears to be awry with my one server.
Both servers have the brand new iLO 2.15 (Apr 18, 2020) firmware and have the iLO Advanced license installed. I even did a factory reset of the iLO card on the problem server and reconfigured it from stratch. Still the same issues.
Anyone have any suggestions before I contact HP for hardware support?
Dave
hello everyone, I have a sata hdd 2tb toshiba in the e200i smart array and it presents me with a problem: in the writing speed it does not exceed 20 mbps and in reading it works regularly, I also have other sas disks inside and they work perfectly. What do you think the problem may be? Help me, it's for business needs !! thank you immensely, hello.
I have a couple of DL380, G5 machines with the P400 controller. One is running centos 7 with the hpsa.hpsa_allow_any=1. The other is running vmware. They both work fine. If I try to use centos 8 it doesn't see the P400 disk at all. If I grab a later version of Centos7 it doesn't see it. I have the latest kernel on the centos 7 machine and it boots up just fine even though I don't see the parm in the module library file. The P400 cards seem to be running version 7.22.
I found a .exe if I had windows 2002. Seems like there would be another way to update the card than to use windows. I found a stand alone image that seems to be a CD image. It won't boot.
I figure there has to be a better way to update this and the mother board's bios. I hope the update will help with Centos 8. I hate to replace the machines, they're plenty of power for what they're needed for.
Thanks,
Rob
Hello, can someone help me?
I have a ml350 g6 4gb (2x2gb) 1xE5620
The server start, but without video, the cooler is at maximum, I'm sharing a link with video and photo.
A photo where this is the connected cr7 led is the connected server
The video in which the leds are flashing, except cr7, is when the server is down
