Hi
I have some DL 380 G9 servers with 12 x 32 GB memory modules.
The 12 empty memory slots I would like to fill up with 16 GB modules.
Can they work together if they are same speed or even if they are not?
I think I once was told that they could not.
But mybe that was in generation 8 and not 9.
Hi
i have an hp dl360 gen 10 with intel 4210 and proxmox installed that i would like to connect to an ups.
I was thinking of purchasing an APC Smart-UPS SMC1500IC.
What do you think?
What is the compatibility level of this ups? is it able to hibernate virtual machines when the UPS charge is low?
ps: I accept suggestions.
Sir,
I am using hp proliant ml150 gen9 server with two sas 2tb drive with Raid Configured but one drive not showing Indication outside front panal where drive showing blinking lights, How to check it
Hi, I have a Proliant DL380p Gen8 server, I'm going crazy to upgrade with a Grid k2 GPU. As a guide I upgraded the power supplies to 1200w, replaced the two processors with Xeon-E5-2690v2, I got stuck at the Riser Card point, I purchased the card with these two P/N 728536-001 728537-001, I connected the riser card to the Secondary (processor 2) PCI riser connector, but the card is not seen by VMware Esxi 6.5 among other things in the free slot of the riser I installed the network card that I had on the old riser and that worked correctly, but in this case all the leds of the 4 network ports remain on.
What am I doing wrong? Is the riser compatible?
Thanks
Please share the steps to programatically change the Proliant Serial Numbers
P.S> Admin:
Post was moved as a new topic from
We have a Gen10 server which we have Enabled FIP security mode on the ILO. The server was being monitored by Oneview.
When FIP was enabled we had to reset the password to what it was prior to the change (this is normal behaviour apparently). Oneview is unable to communicate with the device though. When you perform a refresh in Oneview it states that it is unable to configure SNMP settings on the server ilo, which are required by the appliance for server management.
No changes were made to SNMP settings which were working previously before FIP was enabled.
Has anyone come across this scenarion before and know how to resolve?
Good day HP support
Model: HP proliant Microserver
Processor: AMD Turion II Neo N54L
OS: Windows server 2008
I have recently installed a UPS unit for one of my branches and connected it to our server with a printer cable, yet it requires the installation of a USB-Serial controller driver in order to connect the UPS software to the UPS.
I have exhausted all legitamite means to try and find this driver.
I would appreciate it if someone can help me out with a link to the page where I will be able to download the driver.
Thank you in advance.
Kind regards.
Hello,
I am having some trouble using the Scripting Tools for Windows PowerShell version 3.0.0.0. When I use the Connect-HPEBIOS Cmdlet, I get an error stating "Index was outside the bounds of the array." I am connecting to a HPE Proliant e-series server blade with System ROM version H08 v1.62 and iLo 5 version 2.16. Also I am running on a remote Windows 10 PC. Any help will be greatly appriciated!
Good Day
I am currently having problems with an HP Proliant DL180 G6 server, This server uses Windows Server 2012 R2 as the operating system and has 2 hard drives configured for mirroring, more than a week ago, due to strong electrical variations, the system hard drives were damaged , these were replaced by disks of the same capacity, We tried to start the system restoration using the latest system backup but for some reason the Windows Server 2012 R2 installer disk does not work, it shows the white file loading bar, then appears the blue windows logo, after a few seconds the screen turns black and approximately 2 seconds later the blue screen appears with the message "Your PC ran into a problem and need to restart. We're just collecting some error info, and then we'll restart for you. " we know that the problem is not the DVD since we use several burned in different places apart from the fact that the installation starts properly on other PCs, all the diagnoses indicate that there are no problems with the hardware and also we tried with an earlier version of windows the which is installed without any problem (Windows Server 2008 R2 x64), we also know that hard drives have no problems since they are new and all the diagnoses indicate that they are fine, we are quite confused by this behavior of the server and we have not been able to solve it, We would be very grateful if you can give us an answer that solve this problem since all the administrative processes of the company have been detained for 10 days.
Hello
we have buyed a ML350 Gen 10 server with hpe ethernet 1gb 4-port 369i. So i have try to download all driver fot it and winserver 2019 withour result. Or the driver not see the hardware or not work for OS.
Some help?
Thanks
I have a problem with the HP ProLiant ML350p Gen8 server, actually the Smart Array P420i controller itself. iLo reports an error Cache Module Status Failed, I saw swollen batteries / capacitors from the cache, after replacing nothing has changed. Anyone have any ideas? Maybe need to reset it somehow? Smart Array P420i firmware is 8.32
Hallo zusammen,
ich wollte gerne mal wissen, ob es möglich ist in einen Dl380 G5 mit P400 Controller auch DLL HDD´s einzubauen.
Ich habe 2 Stück eingesetzt, welche mir alle orange angezeigt werden.
Mit scheint das HP das nicht zulässt, oder ich mache etwas falsch.
Kann mir hier jemand helfen?
Google Translate
Hello everybody,
I would like to know if it is possible to install DLL HDDs in a Dl380 G5 with P400 controller.
I have used 2 pieces, which are all shown to me in orange.
I don't think the HP allows that, or I'm doing something wrong.
Can someone help me here?
Hello,
I need to keep two gen8 servers up to date, but I'm a bit confused by the varoious technologies and tools available.
I installed Smart Update Manager (SUM) 8.5.7.
Then I downloaded Service Pack for Proliant (SPP) v.Gen8.1 (6 nov 2017) and used it as baseline for SUM.
This way I've been able to install a bounch of updates.
Unfortunately, the latest SPP for Gen8 servers is quite old, so many updates are not included.
As far as I remember, many years ago there was a tool that used to download updates directly from ftp.hp.com.
Is something similar still available?
Thank you!
Hey all,
Looking for a bit of advice dealing witht hpe amplifier pack. For the most part I have got everything installed correctly and it is playing nice with vcenter. However i'm running into a bit of a problem. From within vcenter, at the step where you go to "add" the spp to the "online software depot" (in the HSM) i keep getting the same error over and over. "Fetching of online depot URL failed. Depot URL not found in SPP details." I've tried rebooting the vcenter and the appliance serveral times but i have no clue what the issue is. Any help would greatly be apperciated!
Hello every one
can i add this system rom(2019.05.24(12 Jun 2019)) https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX-f999a22b47af43ca897c0835be#tab2
to the SPP 2019.09.0 or any other method to upgrade this from current ROM without OS.
Current ROM P70 08/02/2014
Thank you