DL585 G2/G6 shows amber internal health fault LED several minutes after power on
I have a DL585 G2 upgraded to hexacore CPUs so now it reports at a G6. The server runs Solaris 11.2. It has been running fine for years and continues to run fine, but several minutes after boot, the...
View ArticleBSOD en Windows Storage Server 2003
Hi!I havea server withWindowsStorageServer2003 SP2(ProliantDL380G5), whichhas presented severalrestarts, reviewingthe eventsshowsa coderelating toBSOD, however,I have not foundanyrelated datathat...
View Article--- Article Removed ---
*** *** *** RSSing Note: Article removed by member request. *** ***
View ArticleBIOS Update for SE316M1
So i bought a SE316M1 from ebay and was told that it is similar to a Proliant DL160 G6. Well i looked in the BIOS and it has R02. I downloaded the DL160G6 BIOS from the HP website and when I tried...
View ArticlePage Drivers Not Found
Dear, I'm trying to download drivers for my ML310 server, but the page is not working?Does anyone have the same problem?
View ArticleChange SCSI Id of array controller
I have 2 ML570 servers, which have compaq 431 smart array controller cards installed.These cards are connected to a DELL powervault array.I need to setup the cluster for which i need to change the scsi...
View ArticleBroken Smart Array 642 how to substitute it wothout loosing data?
Good Morning,we have an old ML350 G3 with a failed SA 642 (or at least we think it is), some drives are in bad but restarting the server the drives in bad changes. We thouhgt it was a controller...
View ArticleDL380 G4 / 6i and Storageworks 4354r?
I am getting a DL38 G4 with imbedded 6i controller. Does anyone know if it is possible to connect to an existing Storageworks 4354r using the external SCSI connector?Thanks!
View ArticleSmart Array 5i firmware update
Hi,trying to update firmware of SmartArray 5i controller from 1.72 to 2.76. Getting folowing error:Entry Details Severity Error Date / Time 23.10.2008 14:53:11 Message Smart Component, cp009289.exe,...
View ArticleDL360 G5, and new RAID 5 question.
hi, I have a DL360 G5 which has two hard disks. No RAID was done during the install. So now, the OS and applications are set up on the first disk and the second disk though partitioned as E in windows...
View ArticleDL 360 + e200i not enough connectors!
I have two DL 360 which I ordered with the e200i array and 5 drives. I now find that the card only has one connector so I can only attach 4 of my drives. I have been told by HP that I should have...
View ArticleSmart Array 6i controller - Drive failure
Hi, I have a 'replace SMART drive' alert on one of drives on my Proliant DL 380 Server. There are three drives in a RAID 5 setup (distributed data guarding). The OS is windows 2003 and the server looks...
View Articlecpqcisse.sys Memory Issue
Hi there, I am having an issue where it seems the HP Smart Array Notification Driver (cpqcisse.sys) is leaking non-paged pool memory. I confirmed it is this driver by using...
View ArticleDriver needed for Fibre HBA
I have been searching forums and web sites for a few days now and have come up with nothng. I have a DL380 with a StorageWorks 64-Bit/66-Mhz Fibre Host Bus Adapter installed. This was OK with Windows...
View ArticleHow to extend a logical volume under linux (centos 4.4)
Hi all,Using ACU on our DL380 G3 with Smart Array 5i controller, we added a new physical disk to a RAID 5 array and then successfully increased the logical disk to its maximum size (69443 MB).However,...
View ArticleOracle config performance
I am currently at a site that is having Oracle disk i/o performance issue. The current config is a DL380 G4 (3 years old) with 6 146GB 10k RPM scsi disks in a raid 5 array.The array has 2 partitions....
View ArticleError when booting in HP Proliant ML 350 G6
We got attached problem in HP Proliant ML 350 G6 when try to boot As our technican suggestion we replace the slot 0 HDD. Now the server boot up with automatic recovery mode enabled. But now we got the...
View ArticleAdding a processor to an ML350 G6
Hi there! Server newbie here. I'm hoping someone might be kind enough to give me some advice, as I feel like I jumped in the deep end a little. I have built desktop systems before but I know nothing...
View ArticleHP Proliant ML330 G6 not working with UPSes
Hi, I have a server ML330 G6 with one power supply. It is plugged in to a Ups Eaton 5S (1500va, 900w). Despite the fact that the UPS is working properly (I checked it with others devices and other...
View ArticleMicroserver NL54 Gen7
Hello togehter,the server won't start. Power Supply is ok, but the Startbutton on the Server has (Net Power is on) black. Normally ist should by yellow. But there is nothing. The front led on the hp...
View Article