expand logical drive on HP - DL380 G7 on WINDOWS SERVER 2012 R2
hi ALL,we have logical drive raid5 with 6 300GB physical disk, now replaced all 5 disks wich 600GB ones and we are going to replace the last 300GB one woth the 600GB one after this last replace with...
View ArticleML30 Gen 10 Intelligent Provisioning not working
Intelligent Provisioning does not appear to work properly when I can finally get to the configuration page. If a usb flash drive is inserted in the internal of front usb ports, the system hangs until I...
View ArticleML350e g8 v2 - Additional LFF 4-bay cage
Hello.I've recently purchased a ML350e G8 v2 used, and it has one 4-bay cage already installed.I'm looking to install a second cage, but I can't seem to find any vendors with the cage in stock. Is...
View ArticleHow to clear CMOS MEBx on a ProLiant ML10 Gen9
Hello,Yesterday I set a MEBx password on our new ProLiant ML10 Server, and even though I wrote it up I cannot login to MEBx today. btw. The password policy "special characters" isn't pretty user...
View ArticleHow to setup KVM manually on ProLiant ML10 Gen9
Hi,I am trying to set up AMT and KVM using the manual mode described here: https://support.hpe.com/hpsc/doc/public/display?docId=c04996527I can connect to the machine via the AMT Website using the the...
View ArticleExpanding RAID 1 from 2 to 4TB without adding drives - Proliant Microserver...
Hi all,This is my first post here, not sure if i chose the right category so please move if i chose wrong. I am the happy owner of a Proliant Microserver Gen 8, it fulfilling its purpose as backup...
View ArticleILO4 local user has been disabled and ldap authentication doesn't work
any ideas how can i fix ILO ?
View ArticleInstallation issue
Hi,I try to install Windows Server 2012 R2 on a brand new ML110, i100 Raid, 2 x 1TB, 32GB Ram, but it fails.Last command is rmdir c:\boot. I checked out c:, but there is no such directory, so he is...
View ArticleHP DL380P Gen8 - SQL database server -Raid 5 setup - Now need to add more SAS...
Dear Friends,I have two HP DL380p GEN8 hardware setup with same configurations.Using this for SQL database server serviceHyperV replications enabled for Virtual Host (SQL Database server) between two...
View ArticleDL 385 G7 with dual 10g sfp card can't upload more than 11.5 Gbps
Dear communityWe have a HP dl385 g7 with following spec:CPU: AMD Opteron 6234 x2RAM: 8G x10HDD: Samsung 2TB EVO 860 x 7 + (250GB x 1)Network Card: intel x520 dp sfp+Based on HP manual for dl385 g7...
View ArticleHPE ML110 G10 Replacement Bezel
Hi,I wonder if anyone can help me, purchased a new HP ML110 G10 (P03685-425) and unfortunately during the installation the engineer dropped it and the front bezel has cracked. I've gone onto the...
View ArticleNeed Help Reconfiguring an HP DL360 G7
I'm trying to reconfigure this HP DL360 G7 server. It was used as a windows server but was replaced with a new server when the Raid Controller cache went corrupt and we couldn't resolve the issue.I'm...
View ArticleML350e g8 v2 - 6 pin fan connector question.
Hello!I've purchased a ML350 G8 V2 for personal use, and it is currently sitting in my home office, near me while I work. It is quite loud, even at idle.I'm looking to replace the fans with some Noctua...
View ArticleProliant ML350p Gen8 - problems with acu and bay mapping
Hi,i have an proliant server with 16 hdds. in acu I see for hdd, bay 1, 2, 3, 4, 13, 14, 15, 16.The rests all mapped to bay 0. the correct and not correct bays are mixed with port 1 + 2. Array ist...
View ArticleLicense for HP Smart Array SAS
I have changed the three discs of my Proliant D360E server, before I had a RAID5 and now it is not possible, it only allows me to create a RAID0, it indicates to me that the license is not active, how...
View ArticleP440ar Cache Status Details is Cable Error
Hello , I found the server which I maintain blinks the diagnose LED Light in the front of panel. Then I check SSA CLI it shows the following status, what possible root cause it could be? Can someone...
View ArticleProliant DL360 G10 server in UEFI mode . Multiple Disk shown in diskmanagement
Hi Community,Building a new Proliant DL360 G10 server in UEFI mode. OS installed is 2012 r2 standard. 2 x 600 GB HDD in raid 1 partitioned as 100 GB for C and 458 GB for F. I am able to see...
View ArticleClik here to view.
Multiple syslog destinations in an automated way
I'm looking for a way to set multiple remote syslog destinations. I have found out it is possible to add multiple hosts via semicolon (although it is not covered in official iLO User guide):However if...
View Article