Hi everyone,
I'm hoping someone can help me with my request, I'm looking for the pinout for the two System Power Connectors on the top-right edge of the Proliant ML350 G6 motherboard (See Picture). If you own this server but don't know the pinout, I should be able to use detailed pictures of the color order of the connectors to determine the volatages. Thank you for any help!
Hi every one,
I am new in HP community and first time using this community for my quries.
I have HP DL380p Gen8 on which i installed Windows Server 2012R2 , i install HP System Managment but it when i click on HP System Managment HomePage and provide my login id and password after that the response time is very very slow and also pop up some SNMP related error however my i reset in to default setting of SNMP but still error occurs
A timeout occured while loading data for the HP System Managment HomePage which may result in missing or incomplete information.Please ensure that the various agents configuration is correct.One common error is around setting SNMP community strings and having at least one read/write string specified.for additional information on how to discover which components may be causing the timeout , see the HP system Management homepage log and the HP system Management user guide troubleshooting section.
I have HP Proliant DL380 Gen8 and wanted to configure iLO so i just downloaded iLo utility from HP Site and install but when i try to configure iLO i got two errors.
can some please help
Scee Attached Screen Shot Files.
Hello
Why i can't move disk drive from a server to an other ?
i try both method as explained in the SA user guide : Manuel and split mirror.
the new server doent see a valide LUN on the splited disk.
Thank you
Hello
I cant find drivers for this devices (3 same devices) System Interrupt Controller for win2k8r2
Hardware ids : PCI\VEN_8086&DEV_3422&SUBSYS_000B003C&REV_13
Thank you
Hello guys,
I've read quickspecs of Dl380e G8 : http://www8.hp.com/h20195/v2/GetPDF.aspx/c04128166.pdf
it contains SATA 2.5in MU-PLP SC SSD (804613-B21) as compatible for server but when I read also quickspecs of Smart Array P420 :
http://www8.hp.com/h20195/v2/GetPDF.aspx%2Fc04111534.pdf
it does not show SSD above as compatible. My doubt is that Smart array specs are oldest (doc released 2014) and maybe did not include all recent ssd as compatibilty ?
How you suggest to proceed ?
thanks for any advice
Andrea
Good afternoon.
Updating the firmware HP Proliant ML150 G6 cp024879.exe
Unsuccessfully, after the launch here this inscription:
The system only has generic SDR? system will REBOOT after update default SDR!!! Flashing BMC SDR/CONFIG....... Please wait. DO NOT power cycle or reset the system? may take several minutes.....
The message shown on the screen is very buzzing fans, after 7 minutes the server reboots. I waited for 45 minutes, it rebooted 5 times. Nothing changed.
How to fix?
Hello
I cant find drivers for this devices (3 same devices) System Interrupt Controller for Win2k8r2
Hardware ids : PCI\VEN_8086&DEV_3422&SUBSYS_000B003C&REV_13
Thank you
Greeting.
I am looking for the order of DL360e Gen8 NICs, there are 4 NIC on it.
which NIC port is the 1st? beginning with left or right? thanks.
Number 5 pointed is 4 NICs.
Hello
The question is, can i use ILO2 with discrete video card?
Now i see only grey display over web ..
over putty ssh wrote integrated video card is disabled ...
Thank
I have a BL460c G7 that I am trying to repurpose as a test server. I have deployed Windows Server 2012 R2 and pushed the HP SPP 2015.10 but the NICs still will not show up in network connections.
Is there a seperate Emulex driver that anyone knows of that I can install to resolve this issue?
I am getting the following error code:
"This device cannot start. (Code 10)
{Operation Failed}
The requested operation was unsuccessful"
Server: HP BL460c G7
HP SPP version: 2015.10
OS: Windows Server 2012 R2
NIC: HP NC553i Dual Port FLexFabric 10Gb Converged Network Adapter
Driver Version: 10.5.121.7
Thanks,
Tony
The question is simple. I have two HP Proliant DL380G6 servers with a DC Power Supply.
Currently I have two:
Can I just swap that out with one of these AC PART Number:
We are putting into a HP Rack system which I believe is 220.
Hi HP experts,
My DL380 G7 using HP P410i 512 MB Memory + Battery and license Smart Array Advance Pack 1
I have 3 Array :
I would like to expand the RAID 6 Array and extend the logical drive in this array, i am considering delete RAID50 Array and add 6 free disks to RAID6 Array. ( Please open the attachment for detail Hardware and software )
Does my Hardware and software support me to expand RAID6 array and its logical drive without losing data ?
Can i expand array online?
Thank you so much
Is there drivers for the lsi22320bcs-HP scsi ultra 320 for windows xp and windows 2003server?
Thanking you in advance
Abavis Stavros
Naval Architect and Marine Engineer NTUA99
In my DL380 Gen9 with P440ar raid controller, one of the mirrors has failed. The volume says it is queued for rebuilding, but the rebuild never starts. The raid config utility says the drive is fine. There are no error lights on the drive, and activity seems to be occurring.
However, the other drive in the mirror is showing the 'do not remove' light, implying the mirror is broken and only it is operating.
I ran dignostics, and they say
Internal Storage Enclosure Device Failure (Bay 3, Box 3, Port 1I, Slot 0)
Device, Test: Logical Drive 1, Storage Controller in Slot 0 Failed Count: 1 Error Code: F154
Description:
The monitor and performance logs indicate an aborted command failure.
Count: 1
Recommended Repair:
If single drive has ABORTED Command - Re-Seat and monitor. If all drives, then check backplane or cable or Controller.
Device, Test: Logical Drive 1, Storage Controller in Slot 0 Failed Count: 1 Error Code: F297
Description:
Logical Drive status is outside of normal operating parameters.
Recommended Repair:
Refer to the HP Smart Array Controller User Guide for a detailed description of the logical drive state and troubleshooting procedures. The User Guide is available from hp.com.
Last Failure Reason ABORTED COMMAND
Write Errors Retry Recovered 1
Aborted Command Failures 1
So my main question is, how come with all these drive errors, the raid config utility says it's ok, and there are no error lights on the drive?
Secondly, is the best course of action just to replace the drive with a spare and hope it rebuilds ?
Thanks
Hi!
I'm struggling to get my new ML150 G9 to boot from the hard drive. I managed to install CentOS 7.1 without much trouble both in Legacy BIOS and UEFI mode but then after I reboot it claims there are no bootable drives. I have only the single drive connected. I tried unplugging all USB devices, no luck.
The machine has H240 controller (*not* B140i which seems more common) and it's set to HBA mode. When I enter the SSA tool the disk is set as uninitialized but I guess that's normal for non-RAID configuration.
The Intelligent Provisioning tool sounds like a fine idea but CentOS doesn't seem supported.
I`ve just installed a perfect-running Smart Array P212 in my server. It comes with 2.72 firmware version.
My server runs vmware ESXi 6.0 and, after perform a firmware update to 6.64 version from this link: https://h20565.www2.hpe.com/hpsc/swd/public/readIndex?sp4ts.oid=3885794&swLangOid=8&swEnvOid=4115
I perform the installation process correctly, bur after it the system asks to perform a reboot. I went out from esxi shell and reboot the server.
But after it the system shows the message:
HP Smart Array P212 Controller Initializing... +x+
(the rotation mark)
And then it halts. Don`t proceed with the booting process.
I am desperate, because we have some important data in the raid disks.
Please someone help me what can I do to bring the board back to work, please.
hi
my server is hp dl 380G8 and my smart array contoler is p420i with latest firmware :
these are all of my smart rray controler info :
Smart Array P420i in Slot 0 (Embedded)
Bus Interface: PCI
Slot: 0
Serial Number: 0014380279DE940
Cache Serial Number: PBKUD0BRH4Y2GU
RAID 6 (ADG) Status: Enabled
Controller Status: OK
Hardware Revision: B
Firmware Version: 6.68
Rebuild Priority: Low
Expand Priority: High
Surface Scan Delay: 15 secs
Surface Scan Mode: Idle
Queue Depth: Automatic
Monitor and Performance Delay: 60 min
Elevator Sort: Enabled
Degraded Performance Optimization: Disabled
Inconsistency Repair Policy: Disabled
Wait for Cache Room: Disabled
Surface Analysis Inconsistency Notification: Disabled
Post Prompt Timeout: 0 secs
Cache Board Present: True
Cache Status: OK
Cache Ratio: 10% Read / 90% Write
Drive Write Cache: Enabled
Total Cache Size: 2.0 GB
Total Cache Memory Available: 1.8 GB
No-Battery Write Cache: Enabled
SSD Caching RAID5 WriteBack Enabled: False
SSD Caching Version: 1
Cache Backup Power Source: Capacitors
Battery/Capacitor Count: 1
Battery/Capacitor Status: OK
SATA NCQ Supported: True
Spare Activation Mode: Activate on physical drive failure (default)
Controller Temperature (C): 61
Number of Ports: 2 Internal only
Encryption Supported: False
Driver Name: HP HPSA
Driver Version: 5.5.0
Driver Supports HP SSD Smart Path: False
now i put a ssd disk samsung dc on my server dik lights are on but in raid controller not detect ssd disk i have attached ssd disk info
now how can solve the problem?
best reards
Hello,
HP Proliant ML110 G5 no video showing and CPU fan spinning is high all the time.
It was not accessible via network.
It was working on friday. Today it was in such condition.
Tried on different monitors.
Replaced power supply and RAM. Took off the system battery for some time. Not helped.
Hi there,
I have changed the HP p420i controller to hba mode (I need to use ZFS on this server) but I cannot set the boot volume/drive as per the instructions in "HPE Smart Storage Administrator User Guide".
None of the offline modes works as described:
1. Pressing F5 via serial console after Smart Array controller menu does not launch hpssacli as described in the above guide (instead the system goes to HP intelligent provisioning)
2. Runnig HPE SSA from an HP Service Pack for ProLiant(SPP) ISO image works but when entering the command "hpssacli controller slot=0 physicaldrive xx:xx:xx modify bootvolume=primary" responds with "Error: this command is only valid in the offline environment"
Thanks,
Dimitris Beletsiotis
