Quantcast
Channel: ProLiant Servers (ML,DL,SL) topics
Viewing all 10362 articles
Browse latest View live

iLO and Java Plugin


DL360 G7 Blue HDD Led's

$
0
0

I just got a 360G7 server, i setup the hdd's to raid 5 and everything is working well. I have a Debian 8 installation on it currently. What confuses me is all hd's do not display the blue health led. I can manually turn on the LED's on the drives through software provided by HP but they all end up shutting off over time. What could be causing this? how can i get the health LEDs to display?

HP Proliant ML350p Gen8 & ProLiant DL380e Gen8 - SAS card for SAN

$
0
0

Hi,

We need to connect our HP Proliant ML350p Gen8  and ProLiant DL380e Gen8 server to IBM Storwize V3700 SAN.

I was wondering which SAS controller is compatible with HP Proliant ML350p Gen8  and ProLiant DL380e Gen8  server?

We are using Esxi 5.5. Do we need to install any extra driver?

HP insight manager「すべてのシステム」でステータスが変化しない

$
0
0

皆さんこんにちは

HP Insight Managerを導入して1点困った事象があります。

「すべてのシステム」で各サーバ等の状態を一覧します。

「メジャー」が一旦表示された事項は修復が済んだ後、「正常」に戻ると思うのですが、「メジャー」のままです。

当該イベントを確認済、削除しても「すべてのシステム」では「メジャー」となります。左ペインの「システムステータス」では未確認イベントは0になるのですが、右ペインの「すべてのイベント」では「3メジャー」の様にステータスが更新されません。

メジャーのアイコンからiLOやSMHにリンクして飛んでみると、無論ステータスは正常になっています。

Insight Managerのサーバを再起動しても状況は変化しません。

Insight Managerは以下の最新、監視対象は2015.10のSPPを適用しています。

     バージョン: Systems Insight Manager 7.5.0 - Windows      ビルド バージョン: C.07.05.00.00r75rc01      ビルド 日付: 2015-07-30 13:02

 

類似事象などありましたら情報交換お願い致します。

Migration RAID10 to different server

$
0
0

Hi, everyone! I have one problem - MB in my Dl160g8 is crashed. I want migrate RaID-controller and HDD's to another HP server. It's possible? RAID do not broken if hardware is changed?

10Gb/Sec connectivity for DL980 Server with 665249-B21 HP Ethernet 10Gb 2P 560SFP+ Adptr

$
0
0

HI,

 

I am trying to connect my DL980 server to the 10Gb/sec network using the 665249-B21 HP Ethernet 10Gb 2P 560SFP+ Adptr with 455883-B21 SFP transceiver. I amusing Red Hat v6.6. I get no link light, and the status is donw from the OS:-

[root@lxtperpsoa02 ~]# cat /etc/redhat-release
Red Hat Enterprise Linux Server release 6.6 (Santiago)
[root@lxtperpsoa02 ~]# ip addr show eth6
8: eth6: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 8c:dc:d4:b0:6b:c0 brd ff:ff:ff:ff:ff:ff
[root@lxtperpsoa02 ~]# ethtool eth6
Settings for eth6:
Supported ports: [ FIBRE ]
Supported link modes: 10000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: No
Advertised link modes: 10000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Speed: Unknown!
Duplex: Unknown! (255)
Port: Other
PHYAD: 0
Transceiver: external
Auto-negotiation: off
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
Link detected: no

 Do I need to set the speed, I see it does not support autonegotiation?

 

Any suggestions appreciated.

Thanks

Andrew

HP DL180 G6, get raid status

$
0
0

Hello everyone! I have two rack mounted servers HP DL180 G6, with RAID1 (Mirror) in them. The question is - that the programs can obtain raid status, diagnostics?. And provide it with GUI for user .
I have easy set-up cd with "HP ProLiant 100-Series Management Controller" and "HP ProLiant Smart Array SAS/SATA Event Notification Service for Windows Server 2003 and Windows Server 2008 x64 Editions". Does it all that i need?

No RSS available under HP DL380 G6 and NC 382i

$
0
0

My test server is a HP DL380 G6, which according the docs and drivers supports RSS (Receive Side Scaling).  However, using Powershell under Win Server 2012 R2, the RSS option shows "False" under RSS capable.  The latest Driver is installed.  I have ensured the RSS is enabled under advance settings.

I ran a forum search here, and although the new forum format here is very difficult and arduous to search, came up empty.

How do I enable RSS on the NC 382i network adapters under Win 2012 R2?


Server Shutting down due to Excess Temperature

$
0
0

Hey Guys,

We got a couple of brand new out of the box DL 380 Gen 9 servers.

One of them though has some over heating issue.

In the HP Integrated Log I Can see the following. 

>>>

Automatic Operating System Shutdown intiated due to Overheat condition.

System Overheating (Temperature Sensor 1, Location Ambient, Temperature 56 C)

>>>

Though when the system reboots I  can see an ambient Inlet temperature of around 18-20 Always.

Sometimes it comes up, sometimes it keeps rebooting possibly due to the temperature issue.

I have tested the FANs and the Diagnostics dont show any error. I also updated all firmware through SSP.

My gut feeling is that ther emay be an issue with Sensor 1, 

Any idea where that would be located in the server? Any clue what could be the issue ?

Suggestions or comments would be greatly appreciated.

Thanks,

Sanath

Status "all systems" is not updated on HP insight manager

$
0
0

Hello everyone.


I installed HP Insight Manager , and there is one point troubled event.

On the "all systems" I checked status of servers.

After matters "major" is displayed once although repair, I think back to the "normal", but remains "major".

After check the event , delete it , in the "All Systems" the status remains "major".

On the left pane "System Status" , the unconfirmed events  is to be 0

but on the right pane , "3 Major" is not updated.

I fly link on "major" icon to iLO or SMH, of course status has become normal.


I try to restart the Insight Manager server , the situation does not change.

Insight Manager is following the latest, servers has applied the SPP of 2,015.10.

Version: Systems Insight Manager 7.5.0 - Windows build version: C.07.05.00.00r75rc01 build date: 2015-07-30 13:02

Does someone have information?

 

Regards

HP DL585 G5 server ("PCI CTRL" switches)

$
0
0

HP DL585G5 server user is installing the nvidia quadro fx4600 on the server it does not get detected in BIOS.

user has question regards to the purpose of the "PCI CTRL" switches, which are located next to my "System Maintenance" switches. I have attached the picture please check and advise at the earliest. thanks.

 

ILO failed diagnostic (self test at POST) on ML310e G8

$
0
0

Hi,

yesterday, during POST, after (??) install a usb 3.0 addon card based on nec chipset, I get a

"Controller firmware revision 2.09.00 Embedded media manager failed initialization"

notification on ilo diagnostic page and a notification in POST page.

I removed the add on card, but the message remain, so I think the issue is not related (??) to usb 3.0 card.

I tried to reflash mb firmware and ILO firmware to the latest revision.

Also I reset the ILO and bios, but the message is again here.

I don't think the add on card had damaged the proliant, so I suppose (I hope) there is a method to restore the correct state.

Other that the server is functioning in usual way (esxi 6.0 or Scientific Linux 6.7).

Also the internal SD reader is functioning properly.

Can you help me?? :)

Thank you in advance.

:)Best Regards from Rome :)

Andrea

Prolient ML350 G5 419522-005

$
0
0

Have a Prolient  ML350 G5 419522-005. Upgraded the OS to MS windows server 2012 standard last year.  As of last week, we have had issues with it randomly shutting down. When the server is powered back on it gives a red light (second light down from the top) We have replaced the hard drive it indicated was bad, we have reseated the ram, we replaced one of the power supplies on it last year. We are going to try and replace the other power supply and hope that fix's the issue. Does anyone have any other ideas just incase this doesn't work?

 

Thanks in advance for your help.

Bare Metal Restore ProLiant ML310e Gen8 v2

$
0
0

I've been attempting to execute a BMR on the machine listed in the title. The source machine is a Windows Server 2008 R2 (and identical to the failover) and the BMR file was created using Windows Server Backup.

I boot the failover off a Windows Server 2008 R2 disk, choose Repair and follow the process until I get to the recovery screen. At this time, it fails to find the disk with the BMR image. I've attempted this with both an external SATA dock connected via USB, as well as plugging the HDD directly into one of the drive bays for the server. No matter what I try, I encounter the error "The instruction at XXXXXXXXX referenced memory at XXXXXXXXX. The memory could not be read."

I'd appreciate any solutions, help or even a direction to pursue from the community.

 

Cheers

Smart Array in our DL370 G6

$
0
0

This server has a SATA RAID1 logical drive (2 drives 500 GB each) system boot...no problem

I just added 3 SAS disks and created a RAID 5 logical drive. Both logical drives show up in ACU no problems, no errors. 

Server is Windows 2008 R2 Standard. Problem is when I go to view both logical drives in Windows disk manager; I see both drives but I can't create any paritions or fomat the new SAS logical drive, no option available. I can't understand what is happeneing.

Any suggestions would be appreciated. See image attached...


Ilo error at boot after a firmware update on two DL380 G7

$
0
0

Hi everybody, in a company that i follow we have 3 hp dl380 G7, one Virtual Center with Windows 2008 and two Esx with VMware.

In an esx i had see several purple screen, so i updated the firmwares with an Hp smartupgrade firware dvd and the purple screens disapperead..but!

I've done the update on all the 3 server and now the Windows one work fine and the 2 esx can't find the Ilo at the boot...ouch!

Reboot doesn't helped..so what can i do?

HP DL380p Gen8 Server won't boot after installing Hyper-V Role

$
0
0

Hi Everyone

Has anyone noted out in the field HP DL380p Gen8 Servers not booting after installing the Server 2012 (NOT R2) Hyper-V role? 

Here in our test lab, as soon as I installed the Hyper-V role and rebooted, Server 2012  will not start (not even a BSOD) just a blank screen. The PROD Server is Server 2012, so we have to replicate in the test lab for DR purposes.

Product ID: 642120-371 BIOS is P70 07/01/2015 

Intel VTPro etc enabled in BIOS. 

It has a HP D2000 Disk Enclosure attached (PN AJ941A) and that initializes the 24 disks without issue.  I can't see anything in:

HP ProLiant DL380p Gen8 Server - Product documentation

http://h20195.www2.hp.com/v2/default.aspx?cc=us&lc=en&oid=5177957

Any ideas / resolutions most appreciated!

driver needed - System Interrupt Controller

$
0
0

I installed Windows 2008 Server 64 Bits in a ML 350 G6

I applied almost everything that the support page has, but I still have three "System Interrupt Controller" without driver (please see image annexed)

Cam I have some  help?

Thanks in advanced

Do

 

 

EOS HP DL 580 GEn 7

$
0
0

Any idea what the EOS is for the Gen 7 DL580?

Not able to boot off of an external disk

$
0
0

Hi,

I have an HP DL 580 Gen 8. I have an LSI SAS pci card that I would like to use to boot

an external sas drive.  During power on, I do not see the option to go into the bios of the LSI

pci card.  I have a gen 7 and it ask during the power on to hit control S to get into the LSI controller and I am able to go in and enable the "boot" option. Not sure why the gen 8 does not work like the gen 7.

Any clues?

Viewing all 10362 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>