hi.
storage is MSA500.
server is ML350 with SUSE 10 on it.
How to access ACU?
↧
how to access ACU from SUSE
↧
?Random? SNMP traps sent from ProLiant DL360e Gen8 ESXi Host?
Dear HPE Support Community!
We have configured the iLO4 of two DL360e Gen8 and 3 DL380p Gen8 to send SNMP traps to our monitoring server, which is running KS Soft Advanced Host Monitor. There is a strange behaviour going on. The servers which have ESXi 5.5 (with latest updates) installed seem to randomly send SNMP traps (with the iLO Host Name as data). When I get the alerts and log in to vSphere, I can't see any anomalies. Also in iLO4, I can't see any entries in the IML or the iLO Event Log. The DL380p Gen8 servers, which do not have ESXi installed, don't send those traps.
Does anybody have an idea about what I could do?
Many thanks in advance!
Best regards
↧
↧
HP Proliant ML10 v2 cannot boot after environmental power failure
Hi all,
I bought a HP Proliant ML10 v2 a montht ago. I installed Windows Server 2012 R2 Datacenter on it and it was working well until the power failure in my office.
The Windows doesn't boot after the power supply is restored. I see these screens which I think the hard disk is gone ?
Can anyone please suggest me what can I do to fix this ?
Thanks,
Cheekian
↧
Cisco Nexus 5596 - HP SFP compatibility
Hi, I've a HP DL380, and looking to install a couple of 665249-B21 HP Ethernet 10Gb 2-port 560SFP+ Adapter cards to get me up to 10GB connectivity. The switch they'll be connected to will be a cisco nexus 5596. Is there a compatibility matrix anywhere for SPF's compatible the 10GB card, and the switch? Could i potentially install a HP SPF that isnt compatible with the Nexus? Any help would be much Appreciated
↧
Storage device - Local & Remote ???
I purchased 2 DL360 G9 servers with RAID controller P440ar. When I install VMWare ESXi, the system detect that the logical volume (with RAID controller) is remote, not local. I want to ask why it can be like that, and will I meet any issues in the future because of this?
↧
↧
After OA upgrade to 4.50, some of my VC's can no longer communicate with the OA
Hey all,
Seeing if anyone else has had this problem and/or found the solution- after the latest upgrade of OA firmware 4.50(completed last week), it seems some(not all) of my VC's can no longer communicate with their enclosure's OA's. This results in the status on the VC's going Orange, and I am no longer able to assign server profiles to slots. So far this has not caused any interruption. The very maddening part of this is that there is a button to re-enter the OA credentials into the VC. It asks for the OA IP, user name and pw- pretty standard. I can see in the logs on the OA that the login takes place from the VC. However, the VC still remains clueless. Anyone else run across this?
So my OA's are running 4.50(successful upgrades to both OA's), and my VC's are running 4.31.
↧
HP ProLiant ML350 G6 random reboot
Hi!
We have an HP ProLiant ML350 G6 which since january or february, seems to be rebooting randomly. At first, we were not aware of this, as we had no alert configured and was not during production hour. Now, it's happening during the day, causing problem with people working on it.
We tried to look at this, uninstalled the Eaton software and USB cable, as it seems to have started at the same time, no luck. My colleague told me he did update drivers for the NIC, as it was stuck at 100mbps.
I know there is some diagnostic to do again, like updating all drivers, updating Bios and firmware (afraid, if the server reboots :/ ). Windows is Up to date (W2008 R2)
So basically, anyone seen this? We receive email Foundation Agents, SNMP trap: 11020 that the health changed to UNKNOWN then failed, and the server has rebooted little before.
Thanks for any help :)
Edit: all firmware are up to date, from what I saw:
HP Smart Array P410i Controller6.64System ROMD22 08/16/2015Redundant System ROMD22 07/02/2013System ROM BootblockD22 06/20/2009Power Management Controller Firmware2.9iLO2.29 7/16/2015
↧
P410i Array Controllers Handling Predictive Failures
I've had the same problem on various servers using P410i array controllers. Replacing drives in predictive failure with known good drives will not clear the predictive failure. The drives are replaced and go through the rebuild process only to come back online and starting flashing the predictive failure again. As far as I can tell there are no problems. I've had to go so far as to replace all the drives with exactly the same part number/model number drives and completely redo the array and reload the OS. It's acting like the errors aren't cleared out of the controller when the drive is replaced although the ADU shows the new serial numbers. Firmware is up to date and the problem has been occuring through a couple of releases. Any ideas as I currently have one incedent outstanding and I don't want to have them start from scratch just to clear the led.
↧
0 MiB (0.0%) free space Array A-1 Logical Drive(S)
Hi all,
Can anyone explain to me what is it (0 MiB (0.0%) free space Array A-1 Logical Drive(S)
745.1 GiB (33.3%) Free Space Array B with Spare -1 Logical Drive (S)
My Array description showing above message let me know please thanks in advance.
↧
↧
disable blue light ?
I have a Microserver Gen8 G1610T with a blue lighted bar going across the front which is bright enough to light up my living room like a christmas tree. Is there any way to disable this light other than duct tape?
cheers.
mike.
↧
P830I controller keep showing failed in DL580g8
I have DL580g8 and having issues P830i controller. It keeps showing failed status after replacing couple of times.
Updated firmwares for the server, bios and firmware for P830i.
Still same message.
Please advise
↧
Power fault Detected - ProLiant BL420c Gen8
Kindly help on below mentioned IML log error and suggest.
ProLiant BL420c Gen8
SEVERITY="Critical"
CLASS="Power"
DESCRIPTION="System Power Fault Detected (XR: 14 20 MID: FF CD FE D7 03 FF 2F 2F 00 00 08 9C 00 00 F0 F1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00)"
↧
Proliant DL380 G7 wont boot from HDD
Good afternoon,
I have searched the forums here for this problem and I found a few others with similar issues.
My DL380 doesnt attempt to boot from C: it just skips to NIC booting and then fails.
Have looked in BIOS and I see the Smart Array Controller listed as controller 1 and I can watch post messages and the controller initilizes and states 1 logical drive found.
I bunch of PCI embedded devices use IRQ 10 including the controller, is this normal?
Then "drives that were previously unavailble appear available again.
Press F1 or F2
I am thinking I have controller issues but it appears the system recognizes the controller.
Any thing else I should check? Of course this is a domain controller and one of my locations!
Adam
↧
↧
Smart Array B110i SATA RAID disk to port question?
I have a ML server with a built in B110i controller.
I tried to replace a disk that went bad and all kind of bad happened. I assumed that port 3i box 1 bay 3 was the third SATA device.
I need to know for sure what disk goes to wich SATA controller port to get a disk replaced. I attached snippet from the Array config utility.
Thanks ahead of time!
↧
HP Microserver Gen8 Bios Administration Passwort vergessen
Hallo,
ich habe das Problem bei einem HP Gen8 Microserver das das Administrations Passwort für das BIOS vergessen wurde. Ich komme zwar in die ILO oberflächer aber nicht mehr in das Bios.
Wie muss ich weiter vorgehen?
Vielen dank
Armin
↧
Raid P420i running very slow after update firmware
I have 4 ssd speed around 450 mb/s and config raid 0.
My friend use the same P420i and ssd, he tested run 110 vituarl machine in hyper V with 1600mb ram and 1 core cpu. It's working very good,
In my case, after update the firmware, all the vitual machine in Hyper-V can't load to the windows. I tried the disk benmark test is showing the speed like:
SEQ Q32T1 ~ 14mb/s
4k Q32T8 ~ 10mb/s
Seq ~ 1000mb/s
I not good at English, pls help !
↧
How can install win 2008 32 bit on HP server GEN 9
need to install win 2008 32 bit on HP server GEN 9 please help me
↧
↧
A few problems about HDD controllers
I am currently running Windows Server 2012 R2 on an ML350p Gen8 and I want the OS can directly control the HDDs so they can spin-down and can monitor thier performance.
The current config is listed below:
Controller: P420i without cache RAID mode
Array 1: Seagate 500GB, RAID 0
Array 2: Seagate 2TB, RAID 0
(Yes, I gave each physical disk a logical array)
Now I got two extra disks, one 600GB 15K.7 and one 2TB desktop.
I want them to be displayed each as a separated drive in Windows.
I purchased a LSI 9211-8i card and updated P20 controller BIOS and IT mode firmware using my desktop PC.
The card was successfully discovered during my PC POST and was successfully flashed. Then I removed it fROM my PC and installed it on ML350p Gen8, slot 2@processor 1.
I disabled P420I in RBSU and disabled PCI express 3.0 support for slot 2 (9211-8i is a PCIe 2.0 device).
The POST discovered the HBA but a red screen showed up with NMI, log shows uncorrectable PCI express failure 0x00004000.
I removed my HDDs and 9211-8i and converted my P420i to HBA mode using instructions found here: https://hardforum.com/threads/hp-dl380p-gen8-p420i-controller-hbamode.1852528/
After that I powered off the server, installed the HDDs I just removed and booted the server.
POST showed P420i hardware RAID mode disabled, but the server cannot boot into Windows (the server keeps trying network boot).
Here are the problems:
1. Is my 9211-8i malfunctioning or is my server having problems? Or I should have some configuration adjustment before installation?
2. Have anyone successfully booted using P420i's HBA mode? I think it is possible that a drive previously configured as a single drive RAID 0 array cannot be boot directly as a physical drive without RAID configurations.
Thanks in advance.
The current config is listed below:
Controller: P420i without cache RAID mode
Array 1: Seagate 500GB, RAID 0
Array 2: Seagate 2TB, RAID 0
(Yes, I gave each physical disk a logical array)
Now I got two extra disks, one 600GB 15K.7 and one 2TB desktop.
I want them to be displayed each as a separated drive in Windows.
I purchased a LSI 9211-8i card and updated P20 controller BIOS and IT mode firmware using my desktop PC.
The card was successfully discovered during my PC POST and was successfully flashed. Then I removed it fROM my PC and installed it on ML350p Gen8, slot 2@processor 1.
I disabled P420I in RBSU and disabled PCI express 3.0 support for slot 2 (9211-8i is a PCIe 2.0 device).
The POST discovered the HBA but a red screen showed up with NMI, log shows uncorrectable PCI express failure 0x00004000.
I removed my HDDs and 9211-8i and converted my P420i to HBA mode using instructions found here: https://hardforum.com/threads/hp-dl380p-gen8-p420i-controller-hbamode.1852528/
After that I powered off the server, installed the HDDs I just removed and booted the server.
POST showed P420i hardware RAID mode disabled, but the server cannot boot into Windows (the server keeps trying network boot).
Here are the problems:
1. Is my 9211-8i malfunctioning or is my server having problems? Or I should have some configuration adjustment before installation?
2. Have anyone successfully booted using P420i's HBA mode? I think it is possible that a drive previously configured as a single drive RAID 0 array cannot be boot directly as a physical drive without RAID configurations.
Thanks in advance.
↧
How to find the HPE server forums on website
Does anyone know how to find the 'support forums' on HPE website. I get there by complete accident and then can't seem to see all the posts for a particular server (i.e. ML350 gen 9). Is this intentional? Am I only suppose to see the New Post button....or execute a specific search?
↧
ML110 G9 mixing SATA anda SAS Disks
A customer wants to mix 2 SAS 3.5" Hard Disks for NOS (in the primary cage) using the integrated B140i; with 3 SATA 3.5" 2TB Disks for data (in a secondary cage), using a H240 HBA to control the second cage .
Its this configuration supported,
↧