Hello Everyone,
I'm trying to install windows server 2012 R2 Standard edition on a physical svr HP DL380 G9 using Hp inteligent provisioning ver 2.50.164 but when windows installing I got this error "Windows cannot find the Microsoft Software License Terms. Make sure the installation sources are valid and restart the installation"
How can I fix this error?
Dear Team,
I'm trying to expand the storage for my Dl380p Gen8 server. I bought an additional 8 bay cage for this job, Because the existing cage is fully loaded. I need to expand the existing array & I have spent lot of time for the same. finally I got a solution with p830 controller with primary and secondary cable kit. Each cage have 2 SAS ports (2+2 = 4). But the p830 controller have only 2 SAS ports.
My question is “How the cage and controller will connect to each other ?”
I am not getting any picture of the cable from HPE or Internet .If you have this picture please share with me.
Please not I have spent hell lot of time by calling HP level 1 & 2 engineers. They don’t have any single picture of this cable , I have contacted several distributors and supplier & they also not aware of this product. Now what I will do?
Part Number = 698533-B21//729637-001 HP Smart Array P830/4GB FBWC 12Gb 2-ports Int SAS Controller
Part Number = 729278-B21//733719-001 HP 6G SAS P430/830 Primary Cable Kit
Part Number - 729276-B21//733719-001 HP 6G SAS P430/830 Secondary Cable Kit
Hello,
I recently upgraded our 3 dl360 gen8 to the latest spp.
CTRL+S stopped working (I used to configure pxe vlan in there)
Now it just shows this screen (Attachement)
`No Active Broadcom Devices Found!
Press any key to Continue`
Is there any workaround?
PS. All interfaces are enabled for network book in the Bios.
Thank you
I have a DL 120 Gen9 that has a B140i dynamic smart array. The HPE disks are inserted into drive slots one and two. The disk activity light on the drive carriers are solid amber and the Smart Storage Administrator says "there are no configurable physical drives attached to the current array controller".
I'd prefer to not use the DSA because Ubuntu is certified to run on it without the DSA enabled. I'm going to allow mdadm to manage the software mirror volumes.
In the Ubuntu server installation, the installer doesn't see any disks.
The first hurdle is, why are the disk activity lights solid amber? The second would be, how do I get Ubuntu Server installer to see the disks so I can partition and configure them as mdadm managed disks?
Recently, we help customer to add 96 GB of memory to her exisitng DL380 G8 server (which already has 96 GB). It appeared normal after installation (from BIOS and OS level). After that we receive the following alert from iLO : "HPE iLO AlertMail-000: (INFO) POST Information: Processor X, DIMM Y could not be authenticated as genuine HP SmartMemory. Enhanced and extended HP SmartMemory features will not be active.'
Would someone please explain what does it mean in general ? We are sure the RAM package is from HP.
By default, how often will that be sent ? Once during sever start up ?
Searched G8 Toubleshooting guide (https://support.hpe.com/hpsc/doc/public/display?docId=c03257154) but cannot find that alert message.
However, G9 Trouleshooting guide (https://support.hpe.com/hpsc/doc/public/display?docId=c04443553) has that alert message.
Hello all,
I can't seem to find any way to enable "Embedded user partition", that was found via usb settings in BIOS on Gen9 servers. Is the feature removed from gen10 servers? I'm using Proliant DL380 Gen10.
The partition was a perfect place to install ESX on HPE servers. I'm really disappointed, if the feature is removed.
I have a series of DL360's GEN10 that I am unable to install via SCCM, I can manually install these however as I have over 50 to build it's not really viable.
The issues lies when I boot to SCCM for the build and press F8 , running diskpart I see that an array I previously created does not show and I see vol 0 and 1 which both display no media.
You would think that there is a problem with the media, however if I was to go into Intelligent Provisioning and run the scripting toolkit then run diskpart all my drives and arrays show up.
Tried profusely to find a solution, has anyone come across this before and maybe has a solution.
Does anyone know what the scripting toolkit is running ps. I have tried installing the drives whilst in the console and again still no luck.
thanks.
Hi,
Recently we got 4 new 715275-001 (32Gb LRDIMM 1866).
And they are not working with v2 cpus (we got 2628L 2660, 2680)
We thought that modules were dead, but the are new, and we test it in other servers like Supermicro and Dell.
Surprice Modules are working fine with V1 CPUs on all platforms - including our main target - DL360p gen8, and they didn't work with v2 CPUs.
With v1 CPU everehting is working fine - test, memory info - everething is ok (exept lower mem speed, as v1 didn't support 1866)
Is there some kind of special setting or parameter or memory population rules or ... ?
Hi.
How can i find diver for this - HP Proliant ML10 Gen9 Drivers Windows 2016
Good afternoon. You are not right, but after running this HP Proliant ML150 G6 server with 24 GB of RAM Suddenly I am detecting 24 GB, but usable 7.99 GB I have looked with F10, F7 (BIOS) but I do not see where to solve the issue Also MSCONFIG. advanced options, use all the RAM, but neither Any ideas ? since the operating system if it detects me 24 GB
Hi, I hope someone can help. I've just bought a Proliant DL360 G6 and I'd like to set up a game server. I have a copy of WHS 2007. I've set up the RAID array using the onboard D410i and the 4, 146GB SAS drives but when beginning the installation it cannot find the drive. It then asks if I'd like to install storage drivers so I've tried a few for WS2008 + R2 as this was the closest I could find but none worked. I've also tried using the Smart Start utility on booting but that also doesn't have any drivers for any version of WHS. Is there anything I can do to get this running or am I better off buying a proper copy of WS, i.e. 2008?
Thanks in advance,
Jimmy. :)
why the fan on my server development is very fast and noisy, but the activity that happened is not much. is it normal for this type of server?
Dear HPE Friends,
I have a ProLiant ML350 G6 server that was put into services on 5/24/2011. Natually the warranty is out and my customer is dragging their feet on purchasing a new server. At any rate the server is rebooting nearly every morning at the same time and throwing POST errors. After some research I found that the HDDs need their firmware updated. I've lived my entire tech carrer in the Dell world and on top of that I've never had to update firmware on HDDs that are in a RAID configurations. Would someone out there be so kind as to provide me with the proceedure to update the firmware on the HDDs with out destroying the RAID configuration or loosing any data. This server belongs to a medical clinic and is very crucial to their practice. I have very little opportunity for down time so I have to have my game plan down cold. Can someone help with the steps and any management software that might help with this task? I've searched and searched but cannot find anythng that provides me step by step instructions and provides me with reassurance that I will not loose data. See below for specs.
ProLiant ML350 G6
Smart Array P410i
5 Hard drives total
2 HDDs in 1+0 Raid
3 HDDs in RAID 5
Disk Model Number HPDG0300FARVV
Representative Serial Number PFWWX9E
Drive Type SAS
My Gen 8 Microserver fails to startup. it starts fans for a few seconds, then shuts down and re-starts. It the gives a string of POST errors including 0168 0114 0160 4078 5300 5808. I have re-seated RAM, and tried one of the two sticks in different slots, with no effect. Machine hasn't had a year in use yet. Any user checks to be made please?
Hi All,
Let me give you a brief rundown.
I have a Dl380pG8 which had Win 2008 R2 and it was upgraded to Win 2016. Before the upgrade, I had 3 partitions. But after the upgrade, I am left with two. Upon checking, the DL380p is connected to a HP MSA 2040. Additionally during the Win 2016 installation; all three partitions can be seen.
The current configuration of the MSA 2040 was set by a previous employee who has left the company.
Physically the setup of both devices are :
DL 380p connected to switch.
Switch connected to MSA 2040.
How do i reconnect back to the MSA2040 ? Is there any specific software or driver I need to get ? I am unable to find any articles on reconnecting
Hi,
I have ml370 g6 server motherboard. And Power board.
And there are three connectors. one of them consists 32 pins.
Could you please share pinouts for this 32 pin connector.
Hello,
I'm trying to get a new card as in attached photo for my Server HP ProLiant DL585 G7.
Please advise what is the right part number I should look for and what is the name for this specific card.
Regards,
Sameh
