Quantcast
Channel: ProLiant Servers (ML,DL,SL) topics
Viewing all 10362 articles
Browse latest View live

HP DL380 G7 ESXi vmware interface with vSphere

$
0
0

Hello
For testing and inspection I have a HP DL380 G7 ESXi at this new location. I am attempting to access VMware via Vsphere and a web interface to inspect the virtual machines.
The Ipconfig at this location is:
Host Name . . . . . . . . . . . . : ACCENT00
DNS Suffix Search List. . . . . . : socal.rr.com
DHCP Enabled. . . . . . . . . . . : Yes
IPv4 Address. . . . . . . . . . . : 192.168.1.220(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Gateway 192.168.1.1
DHCP Server . . . . . . . . . . . : 192.168.1.1
From a local machine I can ping 192.168.1.1
I cannot ping any ip address configured on HP DL380 G7 ESXi.
The ip addresses on ESXi are:
192.168.1.48
255.255.255.0
192.168.1.1
Primary DNS Server 192.168.1.1


The ESXi ip addresses I was able to change from WMware Management Network though I got an error during those attempts:
"Error setting default gateway failed: unable to set vmkernel gateway address to 192.168.1.1 as there are no vmkernel interfaces on the same network with that ip address"

Let me know what I can do to establish a connected network so that as guest I can access the host to view the virtual machines running on HP DL380 G7 ESXi.
PS is there a way to attach screen shots? Took a few from Management Network....

 

Thanks!


Failed hdd in RAID 1 problem (my scenario)

$
0
0

Hello Dears. I write to you from Azerbaijan. I have 2 x HP proliant DL380 G7 server. One of servers have failed hdd into RAID 1 group. You know yellow amber blinking.  I have bought new SAS drive. I changed failed with new one after shutdown server. But nothing is going on.  System is not boot ESXI. And rebuilding process is not going. Please help me. How can I replace disk and start rebuild process normally with new disk. I searched on Internet but can not find normal answer for RAID 1.

Embedded Flash error gen9

iLO 5 SNMP read stops working after several hours

$
0
0

Hello,

I'm using Zabbix 4 LTS with its standart template for HPE iLO for server monitoring. Every sensors reading working well, but after some time (about 10-12 hours after reset) iLO stops to respond. This problem appears on several ProLiant DL560 Gen10 with iLO 5 (1.35). Only iLO reset helps.

Anyone using Zabbix SNMP for monitoring?

 

SSA "no controllers detected" E208i-a ML350 Gen10

$
0
0

Just got Windows server up and running and installed the smart storage administrator.  This says "No controllers detected."  but it does show the two arrays under "Other Devices".image.png

What is going on with this?  Solutions?

12GB RAM installed, only 4GB available

$
0
0

Dear Expert,

I have HP proliant DL 580 G7 Server. Physical 12 GB RAM is installed in that server but in system properties it is showing only 3.99 GB is usable. 

We have not changed in server suddenly the same is showing. So I have checked the RAM one by one but I am not getting display. I dont know how to troubleshoot.

Please help me

Regards

Vaibhav

Proliant XL420 Gen9 Centos 7.5 and hprcu

$
0
0

i cannot access my ILO either in ssh nor web. I would like to use the LInux system to get network information fron ILO on this server, and if required set a correct IP. 

The server is an proliant xl420 gen9 and the os is a fresh centos 7.5

I downloaded hprcu hp-scripting-tools-11.20-2.rhel7.x86_64.rpm, and installed it and when i run it to read the config  i got this error : 

********:~# hprcu --save
hprcu 5.3.0.0 - HP ROM Configuration Utility
(c) Copyright 2011,2017 Hewlett Packard Enterprise Development LP


---------- System Information ----------
Product Name=ProLiant XL420 Gen9
Sytem ROM Family=U19
System ROM Date=05/21/2018
System Total Memory=131072MB

ERROR: WARNING: Couldn't find the System Default table. System defaults will not be saved in output file.
Hp-rcu return code: 1

And it stops there. 

 

Any hint about why would be required to do, in order to get it working ? 

Raid 5 data lost?

$
0
0

We have a HP StorageWorks server wit ha Smart Array p212. It has 2 SAS array configurations. 

  • Logical drive 1  wich is a RAID 1 configuration 
  • Logical drive 2 wich is a RAID 5 configuration

One of the drives in the raid 5 configuration failed last week an was replace with a new drive of the same model while the machine was turned off.

When the machine was up again i started the rebuild action in the HP Array Configuration Utility. 
This was 4 days ago. I now see in the array configuration utility that all the drives are working and no errors remain. 

But i can not access the data it used to contain. 
When i look at the windows drisk management I can see the drive but is in a RAW format. 
I have also rebooted the server and when booting windows it want to run a checkdisk on the drive. I have done this. It took somewere between 1 and 2 days to complete the checkdisk but at the end it stoped checking and froze. 

 

Could some one please advice me on what to do next. 


Raid 5 array not working after disk replacement?

$
0
0

We have a HP StorageWorks server wit ha Smart Array p212. It has 2 SAS array configurations. 

  • Logical drive 1  wich is a RAID 1 configuration 
  • Logical drive 2 wich is a RAID 5 configuration

One of the drives in the raid 5 configuration failed last week an was replace with a new drive of the same model while the machine was turned off.

When the machine was up again i started the rebuild action in the HP Array Configuration Utility. 
This was 4 days ago. I now see in the array configuration utility that all the drives are working and no errors remain. 

But i can not access the data it used to contain. 
When i look at the windows drisk management I can see the drive but is in a RAW format. 
I have also rebooted the server and when booting windows it want to run a checkdisk on the drive. I have done this. It took somewere between 1 and 2 days to complete the checkdisk but at the end it stoped checking and froze. 

 

Could some one please advice me on what to do next. 

Unable to communicate after f/w update

$
0
0

We have 2 HP IP KVM switches; an AF621A and an AF620A both of which were working fine with the IP KVM Viewer software until we upgraded the firmware on the KVM to version 2.2.0.25242.  Now we get communication errors from the viewer software - specifically the software doesn't see the IP KVM.  Tried upgrading the software to the latest version (4.1.3.2) and still no communication.

Since this started with the firmware update, we tried downgrading the firmware, however that didn't work.  We are able to connect to the KVM by IP address and a browser, just not through the viewer software. 

Any help or suggestions on next steps would be greatly appreciated.  Thanks!

PCI Bus Error (Slot 0, Bus 0, Device 0, Function 0) DL360 G9

$
0
0
Hi.
Server is running on Windows server 2016

At power on state without HDD, all iLO State is green and normal,

At power on state (mean; server is running with HDD and OS is running,) then shutdown from server ‘OS,

Found stopping at shutting down OS screen and Health led is red status.

When check iLO, I found the critical alert at IML log.

Andthen we decided to change the systemboard. After replaced the systemboard the alerts and error messages is still. What happened on this server?

Installing a 8G FC HBA on a DL380G10 Server

$
0
0

Can I still install a QLE2562 card which is 8G in the DL380G10 Server?

In the QuickSpecs of the DL380G10 server it is not showing the card as configurable but am wondering whether can I still use the older 8G FC HBAs on the G10 Servers?

Anywhere I can find this info?

Problem creating logical RAID drives using REST / iLOrest tool

$
0
0

Hey all - looking for an assist. If I'm in the wrong place, please redirect me.

I'm trying to use the iLOrest RESTfulInterface Tool to create some logical drives. I have to replicate this across 50 servers, so I'm trying to script it up. I connected into the server I'm using a s a test (DL360 Gen10, fully patched, iLO5), and I can retrieve all the SmartArray info, drive info, etc. Then I'm trying to create a simple RAID1 mirror of two SSDs for the OS, and another RAID1 mirror of two more SSDs for Data. I'm using these commands:

createlogicaldrive customdrive Raid1 1,2 --name=OS --controller=1

createlogicaldrive customdrive Raid1 3,4 --name=Data --controller=1

So far so good... except when I execute either command, I get the following response:

The property you are trying to change has been updated. Please check entry again  before manipulating it.

And nothing happens on the server. (The DeleteLogicalDrive command works just fine, but not the CreateLogicalDrive command.)

Any ideas? I'd even be open to other methods to script this up, and totally abandon this tool if there's a better route....

Thanks!

Mike

Monitor DP port on the unit Monitor HDMI port

$
0
0

ML 350 GEN10 모델 사용중 본체 DP포트에서 HDMI 모니터로 연결을 위하여 

제가 어떤일을 할 수 있는지 궁금합니다.

금일 서버관련하여 고객센터 문의했더니 서버에서는 디스플레이가 중요하지 않다라고만 답변을 받았네요

이게 무슨 개똥같은 소리인지 궁금하고, 무슨 개같은 논리인지 궁금하네요

서버장비 비싼돈주고 샀는데 모든 기능을 쓸 수 없다면 차라리 반품하는게 나아보이네요

DP포트에서 HDMI포트로 변환잭을 두개나사서 해봤는데 모니터 출력이안되길래 전화했더니 저런 답변받았고,

VGA포트로만 모니터를 쓰라는 소리인지 아니면 DP TO DP가 가능한 모니터까지 구입해서 쓰라는건지

DP TO HDMI 방법 꼭 알려주십시요.

Google Translated

 

Monitor DP port on the unit Monitor HDMI port
Using ML 350 GEN10 model For connection from main body DP port to HDMI monitor

I wonder what I can do.

I contacted the customer center about the server today and I was informed that the server does not display the display.

I wonder what it sounds like, and I wonder what sort of logic it is.

If you can not use all the features, I'd rather return it.

I have bought two conversion jacks from DP port to HDMI port,

Whether you want to use the monitor only with the VGA port or buy a DP to DP monitor

DP TO HDMI Please tell us how.

Can I and how can I expand on my 4 drive system in a dl360e / OR CLONE drives from one array

$
0
0

Hey,

 

I have a DL360e Gen 8. It has 2 slots on the P420 1gb RAID card. I have another slot free. Slot 2 has 4x drives as it ias a 4 drive system.

I would like to either

a) hook up two additional drives via slot 2... but no physical space left.. so I cannot.. but I have another slot?

b) best way to clone and destroy the array and bring data back again plus OS and VM's.

Thanks

R


DL580 g7

$
0
0

I have a DL580G7.  Starts for a few seconds and reboot.  I connect to the ILO 3 and all the sensors are OK.

196","Caution","iLO 3","10/12/2011 08:34","10/12/2011 08:34","1","Server reset.",
"195","Informational","iLO 3","10/12/2011 08:34","10/12/2011 08:33","2","Server power restored."

This happened after I shut  down the server for one week and it didn´turn on. After a lot of work It turned on but the problem described above appeared.  I made it boot today but the disks were not installed so I turn it off and then the same problem. 

 

Best Practice for installing OS and Database on Array

$
0
0

Hello, this is my first server setup and I have a new HPE Proliant ML350 GEN10 Server with 4 each 600GB Drives and an HPE Smart Array P408i-a SR Gen10 controller. My plan is to set up a RAID 5 array using three of the drives while making the fourth drive a Hot Spare. While setting up the RAID 5, I did not see a way to create the C and D partitions. (C for the OS and D for the database.)

After creating the RAID 5 array and installing Windows Server 2016, I booted the OS and resized the drive and created a D partition using Disk Manager in Windows.

Is there a downfall using this configuration?  Should I have purchased more drives and set up the OS separately using RAID 1 and the Data using RAID 5? 

 

Changing to PXE boot (single server)

$
0
0

Hello,

 

I am pretty new to HPOV POSH and would like to change the setting of the first network interface to PXE boot and the Boot order also to PXE and back to Hardisk and no boot of the NIC.

I know how to start and stop blades, but I don't now how to change the settings. I found chaniging a profile in the samples, but not of a singe server

$hpesx = "FQDN Server"

$params= @{

BootOrder          ="PXE";

NIC???_eth0 = "PXE Primary"

}

$servertochange = Get-HPOVServer | where{$_.mpHostInfo[0].mphostname  -match $hpesx}

 

Thanks a lot

DL380 G6 boot problem

$
0
0

Hi

sorry for my poor english :-(

It's my first post and I'm a beginner about server managment

I found a DL380 G6 in my lab and I'm trying to starting up but without any success

I don't see anything on monitor connected via in front vga

when I switch on the server, the situation is with beeping and red led blinking with

all the dimms switch on

after all, I try to switch off/on again and the situaztion becames with only the led proc 1 and 2 switch on

and always the red led blinking

any suggestions?

thanks

 

sorry I'm bot abel to attach image :-(

 

Програмное обеспечение для RAID

$
0
0

Добрый день.

У нас в наличии есть 2 сервера proliant dl380 gen9, из пяти SAS HDD сделан RAID 5.

Есть ли у вас бесплатное программное обеспечение для отслеживании работоспособности жестких дисков?

Viewing all 10362 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>