Hi:
I have a HP Proliant DL380 G5, this server is shutdown turns off after a while. Can someone guide me to solve the problem?
Thank you very much to everyone in advance!
↧
HP Proliant DL380 G5 shutdown it turns off after a while.
↧
Dear SUSE Community, I am installing "SUSE Linux Enterprise Server 12 SP3 Installer for SAP Busines
Dear HPE Community,
I am installing "SUSE Linux Enterprise Server 12 SP3 Installer for SAP Business One" on a "HPE Server Proliant DL380 Gen9".
I am using a DVD containing an ISO image downloaded from https://download.suse.com/Download?buildid=j5aaHMFkICw~
When i boot from this DVD, i am able to start the installation process, i am asked to fill the required information, which i do.
However, when i now click "next" to now complete the installation, the server reboots .
When i now want to reboot from the hard disk, i get the following message below:
can't read ctr while initializing i8042 hp proliant
No caching node page found
Assuming drive cache: write through
How can i be able to resolve this and proceed?
Thanks,
Davis
↧
↧
"can't read ctr while initializing i8042" Issue in "hp proliant DL380 Gen9"
Dear HPE Community,
I am installing "SUSE Linux Enterprise Server 12 SP3 Installer for SAP Business One" on a "HPE Server Proliant DL380 Gen9".
I am using a DVD containing an ISO image downloaded from https://download.suse.com/Download?buildid=j5aaHMFkICw~
When i boot from this DVD, i am able to start the installation process, i am asked to fill the required information, which i do.
However, when i now click "next" to now complete the installation, the server reboots .
When i now want to reboot from the hard disk, i get the following message below:
can't read ctr while initializing i8042 hp proliant
No caching node page found
Assuming drive cache: write through
How can i be able to resolve this and proceed?
Thanks,
Davis
↧
HP 10gb 530 sfp+ 2port on hpe server DL380g9
Hi ;
NIC: HP 10gb 530 sfp+ 2port
I have installed Windows Server 2016 on Server DL380g9. The Windows Server 2016 does not detect the network card, but the BIOS is the network card server. What solution do you have to solve this problem?
↧
is it possible to fetch Server OS information from HP ILO
Hi Team
I'm looking for an option to fetch Server OS details from the HP ILO using any HP utilities like hponcfg or redfish api
we have a lot of HP H/W Servers which are idle for a longtime. these are not accessible currenlty and can't login each ILO console to get OS details
Thanks
317
↧
↧
can we configure Raid 1 on Gen8 and Gen9 Via Powershell ?
Hi Friends,
New bee here and also for Physical Servers too,
basically we trying to automate the Server deployment task ( Configure the BIOS settings + Configure the RAID 1 + Deploy OS + Deploy the respective Service Pack ) using ( Orchestrator and SCCM )
i would be using SCCM 1810 for the OSD + Serverpack installation part,
i need help with configuring RAID 1 , i found smart array commandlets but i read that they support starting from Gen 10 and not for Gen 8 & 9 , ?
is there any way to achieve this ? if anyone has step by step guide etc please share
any guidence will be highly appreaciated
Thank you !!!
Tanoj
↧
Updating drivers/firmware with SUM 8.4 on Gen10
When I'm trying to update some hosts with SUM, I keep getting this error now where before I never did.
Warning: Integrated Smart Update Tools was not running on the OS. If components are selected to install via an iLO install set that require installation in the OS then they will not run unless iSUT or Smart Update Manager are run.
I've been trying to get this iSUT figure out, but the documentation makes no sense. I was wondering if anyone has figured this out on how to get it installed. I've been going through so much documentation but it seems so poorly documented.
Any help would be greatly appreciated
↧
iLo Firmware Vcenter
I have two ProLiant DL360 Gen10 servers. Both are currently on iLo5 firmware 1.37. I am attempting to update, it appears there is an update to 1.40. I have gone to HPE Support to download the update, but I am very confused on how to install this update. I tried to download the package that shows up under those search results (S independent: RECOMMENDED * Online ROM Flash Firmware Package - HPE Integrated Lights-Out 5 (ilo5_140.fwpkg))
In order to install this the instructions say:
To flash this firmware package, use the following iLOrest command. See http://www.hpe.com/servers/resttool to download the latest version of the iLOrest tool.
If I try to download this though, there is only a Linux Version and Windows Version, but no Vcenter verion. I haven't worked on HP Servres before, but I feel like I'm missing something. Does anyone have any experience they can share with how to update the iLo Firmware in this setup? I have read and watched youtube videos when using Windows servers, but can't find much for Vcenter.
Thanks You.
↧
ML110 G7 Case Fans
Hi,
I'm going to prefix this by saying this server is used for home NAS purposes and is out of warranty so I don't "care" about HPE support.
I needed more disk slots than this server provides so I have transplanted the internals into a much bigger case (11x 5.25" drive bays with 3x 5-in-3 hot-swap caddies) and added 2 HPE H240 HBAs to connect them all. So far, so good... except the fans.
This server comes with a 92mm rear fan and an 80mm front fan. At least the 80mm one gets WAY too noisy for a home environment plus my replacement case only has mounting holes for 120mm fans. So I tried with Noctua's Industrial 3000RPM 4-pin PWM fan but I get a flashing red light and:
1611-Fan 3 Failure
Fan Solution Not Sufficient
Even though the Noctua has more CFM; 109.8 vs 86.44. I even tried disconnecting the PWM wire so the fan spins at full all the time with no luck, so it seems HP are forcing a minimum RPM on power-on to determine a 'sufficient cooling solution', whch is totally illogical because air flow > RPM!!
So bascially, what 120mm 4-pin PWM fans exist that aren't jet engine noisy and won't stop a ML110 board from booting. Do any of HPE's other non-enterprise servers come with 120mm fans that i could use?
Thanks.
↧
↧
Problem installing Windows server 2019 with Intelligent Provisioning on Proliant ML350 Gen10
Hi,
When I'm trying to install Windows server 2019 datacenter on a Proliant ML350 Gen10 server using Intelligent Provisioning, the install halt at this error:
x:\windows\system32>hpev CQTESS=
ERROR: deleting EV CQTESS
<?xml version="1.0" encoding="UTF-8"?>
<EnvironmentVariables Count="0">
<Environment variables>
x:\windows\system32>exit /b 0
x:\windows\system32>
I got those firmwares on the server:
System ROM U41 v2.00
Intelligent Provisioning version : 3.30.213
Someone knows what causing this to fail?
Thanks
↧
HP USB KEY UTILITY cannot process SPP-2019-03
usb key utility version Version:3.0.0.0 not working to make pendrive bootable
↧
776 ready for recovery is queued for rebuilding
Dear
i have server HP ProLiant DL180 G6 with Smart Array P212
i used raid 1 for 2 hdds
fisrt hdd sas 2tb as 3 partitions and in the first partition the windows was installed and we have another 2tb to mirror using raid 1 the first hdd
also we have sas ssd 256gb raid 1 with another one
all in working gd but i have problem that in the partition where the windows installed the array always say that Ready for Recovery (is queued for rebuilding) but doesnt rebuild
all the others partitions ( logical drive) rebuild normaly and work fine
what should i do???
i upload and attached the report from array
hope to get help
Thank you
↧
Proliant Dl360e gen8 abrupt shut down for NIC Interface
Hi,
We have a Oracle RAC deployment(on OEL 6.4) with two nodes(Proliant Dl360e gen8) connected each other through private LAN through a CISCO mananaged switch.
Recently we have observed that any status change(up/down/freeze) in the Private LAN NIC causes one of the node(standby node) to reboot abruptly.Later we connected the two nodes directly through ethernet cable bypassing the switch and after a while one of the standby node got rebooted abruptly.
We still do not understand the root cause of the problem and looking for some input from this forum.
Thanks in advance.
↧
↧
SAS drive Firmware Update recommended but can't find an update
Hi there,
We have a proliant Gen 8 running 2008 R2 and recently one of the drives failed, so I got a new one but the Smart Storage Administrator software is saying the firmware should be updated from HPD2 to a minimum HPD4 .. problem is the latest one I can find for the drive is HPD2.
Drive: HPE 300GB SAS 6G Enterprise 10K SFF
Model: HP EG000300JWFVB (It says this model is a 12 GBPS but it's definitly 6)
Any help would be appreciated, thanks!
↧
Proliant dl360p gen8An Unrecoverable SystemError (NMI)has occurred (iLO application watchdog timeout
An Unrecoverable System Error (NMI) has occurred (iLO application watchdog timeout NMI, Service Information: 0x0000002B, 0x00000000)
Hi All ,
We have one DL380p gen 8 server runnign Red Hat Enterprise Linux Server Release 6.2, it is second time that server crashed and reboot with the following IML logs :
ASR 04/24/2019 22:00 04/24/2019 22:00 1 ASR Detected by System ROM
System Error 04/24/2019 21:58 04/24/2019 21:58 1 An Unrecoverable System Error (NMI) has occurred (iLO application watchdog timeout NMI, Service Information: 0x0000002B, 0x00000000)
sys logs :
========================================
Apr 24 22:01:54 prs3-tir hp-ams[2834]: hpHelper Started . .
Apr 24 22:02:08 prs3-tir hpasmlited[2895]: hpDeferSPDThread: Starting thread to collect DIMM SPD Data.
Apr 24 22:02:08 prs3-tir hpasmlited[2895]: Initialize data structures succesful
Apr 24 22:02:13 prs3-tir hp-ams[2834]: CRITICAL: An Unrecoverable System Error (NMI) has occurred (iLO application watchdog timeout NMI, Service Information: 0x0000002B, 0x00000000)
Apr 24 22:02:14 prs3-tir hp-ams[2834]: CRITICAL: ASR Detected by System ROM
Apr 24 22:02:15 prs3-tir hpasrd[2922]: Starting with poll 1 and timeout 600
Apr 24 22:02:15 prs3-tir hpasrd[2922]: Setting the watchdog timer.
Apr 24 22:02:15 prs3-tir hpasrd[2922]: Found iLO memory at 0xf7df0000.
Apr 24 22:02:15 prs3-tir hpasrd[2922]: Successfully mapped device.
Apr 24 22:02:15 prs3-tir cmanicd: Entering iml_log_link_up(slot: 0, port: 1)
Apr 24 22:02:15 prs3-tir cmanicd: Entering get_event_id(slot: 0, port: 1
Apr 24 22:02:47 prs3-tir hpasmlited[2895]: hpDeferSPDThread: End of Collecting DIMM SPD data.
Apr 24 22:02:48 prs3-tir cmanicd: Existing event id(4) found for the slot and port.
Apr 24 22:02:48 prs3-tir cmanicd: Entering repair_iml_event(slot: 0, port: 1, event: 4)
Apr 24 22:02:48 prs3-tir cmanicd: Entering read_iml_event(slot: 0, port: 1, eventid: 4)
Apr 24 22:02:48 prs3-tir cmanicd: Calling ioctl() to read event id: 4)
Apr 24 22:02:48 prs3-tir cmanicd: Successfully read the event id: 4)
Apr 24 22:02:48 prs3-tir cmanicd: Trying to repair the existing IML Event.
Apr 24 22:02:48 prs3-tir cmanicd: Successfully repaired the IML Event.
Apr 24 22:02:48 prs3-tir cmanicd: Returning from repair_iml_event().
=======================================================
Any one has faced this issue and know how to resolve?
Thanks in Advacnce
Florant
↧
HP USB KEY UTILITY cannot process SPP-2019-03
hpe usb key utility not working i tried
1)Hpe usb key ulitity latest version
2)Rufus
3)Iso to Usb
tried But No Luck
↧
dl360 gen10 vmware deployment
Dear all,
Who can help with following issue:
unboxed dl360 gen10 server - hpe rapid setup used to create logical drives and OS (vmware) deployment. Everything seems to be ok till the server reboots and start everything over and over again. It seems like there is some kind of overlooked "save all" bouton in order to lock the configuration down... Can someone of you be so kind and try to explain what's going on? Any input is more than welcome!
Thank you very much
↧
↧
P822 RAID Controller from an HP DL380 Gen8 to DL380 Gen10
Can one move the P822 RAID Controller from an HP DL380 Gen8 and the two external storage enclosures to a new DL380 Gen10? The long term goal is to upgrade the RAID Controller and the older MSA60 and the less older D2600, but for now just want to get them up and running.
↧
Uptime monitoring
I have two servers DL180 and DL 60 with Vmware 6.5 and Vmware 6.0 OS. I want find and monitoring server uptime .
↧
HP Proliant ML110 G6 - standby (sleep) not available
Hello, I work in a small no-profit organization, and we got as a donation an old, but perfectly working ML110 G6 to use in our lab for education activities of unemployed people. Since the orignal owner bankrupt I don't have access to official support or download of stuff like bios update.
I've installed Windows 10 on it and it works flawlessly (with a NVIDIA video card we bought), even if I guess it's supposed to work with Windows Server. Only glitch: sleep is not available neither in start menu nor as an option in power management control panel. Tried as usual under "choose what power button does" and I have only "fast boot", "hybernate" and "lock". It's weird because I can hybernate without problems, but not put the machine into sleep.
I've installed latest video card drivers as suggested elsewhere, but nothing changed.
Is there some driver I can install to fix it, or is it an hardware incompatibility because it's a server?
It's not a major issue, we can live without it especially because hybernation works, but if it possible I'd like to fix it.
Thanks in advance!
↧