Quantcast
Viewing all 10362 articles
Browse latest View live
↧

Reinstalled OS on ProLiant DL380p Gen8, what HP software should I install?

July 14, 2019, 3:36 pm
$
0
0

I have almost no expsoure to HP servers so please bear with me. I have reinstalled windows server 2012 R2 on a ProLiant DL380p Gen8 that previously had the SP's through 2017.04.0 installed on it. I have already installed "HP System Management Homepage for Windows x64", but it shows almost nothing in comparison with what it showed before the OS reinstall. A message at the bottom of the Management homepage says "Install the latest version of HP Insight Management WBEM Providers and/or HP Insight management Agents from HP Service Pack for ProLiant(HP SPP). Click Here to the latest version of HP SPP." Probably these components came preinstalled on the server when it was first acquired? Should I install both?

Also I think I've configured iLO for port 192.168.4.10, but when I browse to that address there is nothing. Do I need to install "HP Lights-Out Online Configuration Utility for Windows x64 Editions"? iLO was never configured on this server as far as I can tell. Otherwise how else do I access iLO?

↧
Search

FAULT DETECTION HARD DISK from HP Proliant DL360 G9

July 12, 2019, 6:10 am
$
0
0

Hi Dear all ! Please, how to make a prolific DL360 G9 server able to detect its hard disks when the component. the smart controller component?

↧
↧

Boot from Crucial SSD. HP ML110G7

July 13, 2019, 4:01 am
$
0
0

Hi.  I have an ML110G7 running Win7 Pro SP3.   I've cloned the OS to a crucial MX500 SSD card, but it hangs at the post screen.     I read somewhere else that the solution is to install a bootloader like Grub to an SD card, but I can't find that forum or thread any more, so I'm not sure if that's worth pursuing or if there is a simpler answer.   

Any suggestions that may help resolve this problem would be appreciated. 

 

Many thanks,  Alan.  

↧

Update Bios DL180 Gen9 v1.20 to 2.72

July 14, 2019, 7:49 pm
$
0
0

Good day, I want to update the Bios of my HP DL180 Gen9 server that has the version 1.20 update to the latest available 2.72, the update would be done remotely by ILO 2.70, but I have the fear of updating it if it is safe to do it ?

I also want to know if I should update version by version or I can update it at once to 2.72

↧

DL380e Gen8 Upgrade CPU from Xeon E5 - 2407 to Xeon E5 2450 V2

July 15, 2019, 1:32 am
$
0
0

Hello,
I would like to upgrade an DL380e Gen8 Server with one Intel Xeon E5 2407 CPU with two Intel Xeon E5 2450 V2 processors. The processors fit easily on the sockets. RAM is also installed for both CPUs.
It seams that both Xeon E5 2450 V2 processors are not working -> black screen, bios is not running.
If I install two Intel Xeon E5 2407 processors the system is running.
I also test the server with only one Xeon E5 2450 V2 processor. Same problem -> black screen, bios is not running.

Does the Xeon E5 2450 V2 processor needs another power supply?
Does anyone know the problem?

Thanks for all replies.

↧
↧

Server not booting after swap HD

July 15, 2019, 2:05 am
$
0
0

Hi evrybody,

 

i have server proliant ML350p G8 with 2 HD on RAID1.

both HD giving aleart.

so i shutdown the server replace HD0 with new one.

tern on server and go to HP Smart Array Controllers & rebild the RAID.

after rebild completed i reboot the server but it is not going to windows 2012 server !!

any suggestion ?

 

thanks

↧

Deletion Process of the Logical Drive takes really long

July 15, 2019, 2:39 am
$
0
0

Hi,

I started the deletion of the logical drive on our dl360 Gen9 last thursday (July 11th) and it is still deleting (July 15th). The Array consist of 4 x 1,2 TB SAS HDDs clustered in a RAID6. Does it usually take so long for the logical to delete and if not, can you suggest what I could do to solve that issue?

Thanks

↧

Intelligent Provisioning not starting

July 15, 2019, 7:36 am
$
0
0

Hello,

I am triyin to instal plesk + Ubuntu in a ProLiant DL380 GEN10 Server.

I have tried to start the intelligence provisioning to access an ISO in a pendrive, but the IP gets stuck in the "Intelligent Provisioning - Waiting for ILO to response" screen.

I've tried before to boot from an USB, but the UEFI is not working, and the Legacy mode neither (it always loads the boot menu. I slect the "Legacy one time boot" option and when rebooting, i get to the menu again, and i get stuck in that loop)

Thank you

 

 

↧
Search

Riser kit for DL360 G10

July 16, 2019, 4:49 am
$
0
0

Hello,

I have the below described server configuration. It appears that both NIC cards are mapped to same CPU.

As I need to have one NIC per CPU, can someone please indicate which riser kit is to be ordered for this config?

867958-B21 HPE DL360 Gen10 4LFF CTO Server

870968-L21 HPE DL360 Gen10 Xeon-G 6138 FIO Kit

870968-B21 HPE DL360 Gen10 Xeon-G 6138 Kit

815100-B21 HPE 32GB 2Rx4 PC4-2666V-R Smart Kit

875490-B21 HPE 480GB SATA MU M.2 2280 DS SSD

867978-B21 HPE DL360 Gen10 SATA M.2 2280 Riser Kit

817753-B21 HPE Eth 10/25Gb 2P 640SFP28 Adptr

817749-B21 HPE Eth 10/25Gb 2P 640FLR-SFP28 Adptr

871244-B21 HPE DL360 Gen10 High Perf Fan Kit

865414-B21 HPE 800W FS Plat Ht Plg LH Pwr Sply Kit

 

 

Thank you

↧
↧

HPE DL20 Gen10 Max Memory

July 17, 2019, 1:24 am
$
0
0

Dear Community, 

In the quickspecs of the DL20 Gen10 it is stated that it can max handle 64GB memory max.

But on several reviews it is written that when Intel will support 128GB ram on its e-2100 xeon CPU's the DL20 Gen10 will support it to. 

According to Intel ark the cpu's now support 128GB ram. Does the DL20 Gen10 support it to? 

Thanks in advance

Romke

 

 

↧

DL380Gen10 with all-NVMe for SuSE OpenStack Cloud, NVMe handling, limits, bottlenecks

July 17, 2019, 2:25 am
$
0
0

Hi,

we plan to use Dl380Gen10 servers for our new SuSE OpenStack Cloud / SuSE Enterprise Storage (Ceph). As NVMes are getting cheaper and it would eliminate the need for array controllers we think about an all-NVMe setup with 2 NVMEs for boot (SLES) and 2 or more NVMes for Ceph OSD's 

I found this HPE document:

https://h20195.www2.hpe.com/v2/getpdf.aspx/4aa6-3464enw.pdf

Q: Can NVMe drives be used for operating system boot purposes?
A: NVMe 2.5" SSDs work in UEFI and legacy modes, but there is no boot support at this time. The drive performance would be best used for
workloads that demand faster data access

Also, Hot Swap seems to supported, but not Hot Add.

Questions:

- with NVMes only software RAID is possible?

- is it now possible to boot SLES from NVMe and a sw raid1? I heard that this should be woking with SES.

- Hot Swap is nice, but a downtime for Hot Add (Expansion) is not so nice, is this still the case?

- what about the bandwith needed for a large number of NVMe devices? What is the bottlenck if we want to put 10+ NVMes in a serve? PCI bus?

Anyone here using (all) NVMes setup with SLES or any other Linux, how is this working is operations? Other things than the mentioned that I should think about?

 

 

 

↧

Is Intel x520 10 Gigabit NIC compatible with ProLiant DL380 Gen9 server?

July 17, 2019, 6:00 am
$
0
0

Hi.

I wonder if Intel x520 10 Gigabit NIC is compatible with ProLiant DL380 Gen9 server? I can't find any information/HCL. I have installed it and it is recognized correctly in server's BIOS, but firmware version information is empty, and server start fails with red screen showing CPU registers contents. I have tried ProLiant service pack and it installed NIC drivers, but firmware info is still empty, and start fails again.

If that configuration is supported where can I download drivers/firmware for that NIC model?

 

Thanks in advance

Kerim1

↧

HP ML350 Gen9 no bootable devices found

July 17, 2019, 2:18 pm
$
0
0

Hello,

My HP server has 2 controllers:

1. P840 - 12 disks. RAID 5. Red Hat Linux boots off this

2. P440ar - 8 disk. RAID 5. Now there was a failed disk on this controller. Then another one failed. 

 

The system is was flashing red. No bootable devices found.

Removed P440ar from motherboard. System is green. But still no bootable devices found. 

Can I remove the P840 controller, reset mother board, reinsert controller and RAID configuration won't be lost?

Is this a known issue? P840 and P440ar sometimes conflicts? 

↧
↧

The computer has rebooted from a bugcheck. The bugcheck was: 0x0000007e - [ProLiant DL380 Gen10]

July 17, 2019, 9:47 pm
$
0
0

I use the ProLiant DL380 Gen10 , The Server restart 2 time in 2 week.

In system log show as below : 

The computer has rebooted from a bugcheck. The bugcheck was: 0x0000007e (0xffffffffc0000005, 0xfffff801cddce963, 0xffffd000b36ee058, 0xffffd000b36ed870).

Could you please help to solve the issue.

Thank you,

↧

Dl 360e Gen8 onboard SATA and SD

July 18, 2019, 2:45 am
$
0
0

Hi all,

I'm looking for some info regarding onboard SATA, slimline SATA and SD card port.

I just get DL 360e G8 LFF for my home lab. I wanted to install light weight OS either on SD card, or Windows Server on SSD. Problem is that It's not detecting SD card at all (i tried three of them including HP branded), does anyone has some experience with it?  Then I tried connecting SSD to SATA port on board and that's the other question. 

There is a SATA port called rear SATA but no power connector, I supplied power from the connector which goes to caddies and tested it on 2.5" HDD. Drive is spinning but not detected by the system. Does not matter what SATA option I set up in BIOS RAID b120i, EHCI SATA or legacy SATA. Only drives in the caddies are detected during controller initialization. Same goes for iLO only caddies’ drives are visible

I'm have done the BIOS upgrade to ver 2019 and iLO4 2.70.  The only thing which changed after the iLO update was the fan speed from 26% to 38% is there any way to downgrade iLO version?

I haven't tried slimline SATA (for optical drive), I would have to order adapter cable to test it.

Does anyone have some experience with that? What's the rear SATA connector intended use?

 

Thanks in advance

Foxy

 

↧
Search

HPE ESXi 6.5 or 6.7 for DL 380e Gen8

July 18, 2019, 3:38 am
$
0
0

Dear All,
I'm looking for an HPE ESXi 6.5 or 6.7 Iso file for dl 380e Gen8 servers.
In the HP server matrix is marked that only 6.0 is supported.
Did any one has build an iso for ESXi  6.5 or 6.7 for DL 380e gen8 or can say how to build such an iso.

Best regards

↧

Replacement drives for ML350p Gen8

July 18, 2019, 2:31 pm
$
0
0

I have a ML350p Gen8 server that I have expanded drive capacity in to be able to hold 24 SFF drives with a P420i controller.

Per this document: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c03263146&docLocale=en_US

The largest SFF drives I can put in this server are 1.2 TB drives (i.e. 697574-B21).

On: https://harddrivesdirect.com/proliant_build_ML350p_G8_Hard_Drives.php

Are the larger drives (i.e. 2TB 765466-B21) compatible with my server?) What would be the largest HPE drives I could put into this system?

↧
↧

Install and Configure disappear

July 19, 2019, 7:00 am
$
0
0

Good day.
I would appreciate it if someone can assist me.
I have a ProLiant XL170r Gen9 servers.
System ROM is U14 v2.72 (03/25/2019).
iLO firmware version is 2.70 May 07 2019.
I updated the Intelligent Provisioning with HPIP271.2019_0102.140.iso
The problem I'm having is that the "Install and Configure" disappears from Intelligent Provisioning.
Regards
Chris

↧

Change power supply HPE ML110 G9

July 19, 2019, 7:50 am
$
0
0

Hello good afternoon.

I wanted to ask you if you can incorporate to this server a power supply other than the one that sells the HP brand, and be able to incorporate a Seasonic brand commercial in which you can choose a higher level of efficiency and high quality components, since the server is 365 days a year on.

Thank you.

↧

Proliant ML30 gen10 dedicated vga problem!

July 21, 2019, 5:12 am
$
0
0

Hi, I'm trying to mount a dedicated vga (nvidia 1030) on a ml30 gen10, but when I mount it, it performs the initial check (all ok), then it stuck on the hp enterprise logo and doesn't continue, it doesn't appear
the screen where you can press F10 to enter Ilo, any idea ??

↧
Viewing all 10362 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>