Hi Experts
I have a HP Gen 9 server ( Live server of the client and not the test system ) .. accidently one of the logical group in that server was setup in RAID 6 and we wanted it to be in RAID 5. Please suggest a way to migrate from RAID 6 to RAID 5 without losing a single data. Server is having P440 Array Controller.
Prompt response will be highly appreciated.
thanks.
HP DL380p Gen 8:
After the Proliant service pack "P03093_001_spp-Gen8.1-SPPGen81.4" has been successfully installed, one of our servers does not start anymore.
There is a message that no disks are installed. See screenshot.
I can start the HP Provioning, but the SSA indicates that no disks have been installed. There is no Smart Array Controller.
Any idea?
Hi, I've managed to make use of the ilorest and HPEiLOCmdlets to do some automation (updating firmware/ilo for instance) and the powershell scripts for getting server information. I was wondering if there's any way to download the iLO and BIOS configuration from one server and apply it to another? Recently received a new batch of servers and would really like to automate those BIOS settings. I haven't been able to find commands to do this, so if someone can point me in the right direction or have any ideas I'd appreciate it.
Dear all,
I have got an ML30 G9 entry model (P03704-XXX) with 4 LFF SATA disks - non-hot-plug. Now I got a quite new P440 controller with its battery and cable too that would be available. Currently there are some standard non hot plug sata hdd in use (not mentioned in the quickspecs).
An option would be to buy a 4LFF drive cage, 4x new hdd that are supported then I get a hot plug solution that can be connected to the p440 (I have a wide mini-sas to 2x sff-8087 cable).
But that would nearly cost half the servers original price...
Is there any alternative in order to use that P440 in the server mentioned above?
Thank you!
Backup depository server reboots when under network/disk load.
ml350p gen 8 / 64gb ram / 1 xeon e5 2620 / p420i 2gb / 4x4tb raid 5
Managemnt Log Viewer captures this error (and many similiar)
Critical 109 CPU 3 9/14/2019 20:58 9/14/2019 20:58 1 Uncorrectable Machine Check Exception (Board 0 Processor 1 APIC ID 0x00000003 Bank 0x00000003 Status 0xBE000000'00800400 Address 0x00000000'0000E18A Misc 0x00000000'00000000)
This problem has been in existence since Gen 6 and Gen 7. My server is uptodate on firmware, both motherboard and p420i (2gb) raid controller.
I have found two advisory bulletins published that offer work arounds by changing the bios settings to Maximum Power and Performance and making sure the Ram Frequency is set to AUTO. That has helped but not fixed the problem. The bulletins say that a permanent solution will be forthcoming. WHEN ???? These bulletins were published 5 years ago and 7 years ago - where is the fix????
Advisory Document ID c04046303 : R date 2013-12-13 : U date 2014-03-13
Advisory Document ID c02914393 : R data 2011-07-11 : U date 2012-02-13
I've rotated memory sticks - still reboots, I've added a stand alone sata drive to the motherboard sata ports to bypass the p420i as the target drive for the backup - still reboots, changed cache memory on p420i - still reboots. I've reduced network speed from gigabit to 100 mbps to see if it was saturation in either the network or storage channels - still reboots.
A little help would be most welcome.
Palustec
Hello everyone.
Server DL360p Gen8 was upgraded with memory, 2 x PSU and 2 x E5-2620v2 more than year ago.
One day, maybe month ago, server stopped working and internal health diode blinks rapidly (maybe 3-4 times per second). iLO not responding and server cannot be turned on.
After swapping CPU's, discover that CPU 2 not working. OK, I have to purchase another one. CPU arrives, put it in the server aaaaannnnnd BAM - server not working
With both cpu's installed, after pressing power button, power button diode lights green for few seconds, fans turns on for few seconds, and aftter that server halted with rapidly blinking internal health diode.
Try to update system firmware, I see there is 2019 version release. Update it, iLO also.
Now I can log in with iLO, but 'system health is OK' and in CPU tab there is only one CPU.
Regarding to troubleshooting guide, when internal health diode:
Flashing red = System health is critical.
Fast flashing red = Power fault (Check system and devices)..
With one cpu, installed in first socket server boots and operates normaly.
Does anyone encountered such a problem or any advice how to continue with troubleshooting or I need to replace system board ..(or server)? Thanks in advance.
BR,
P.S. Maybe
Hi,
Is there anyway at all that HP or other software allow you to control fan speeds? I use this in a home office and it's just far too noisy most of the time.
My temps are really good, in relation to the 'Caution' and 'Critical' theshholds HP define, so I don't know why of them is running at 100%. I know the ML100 is an old server now but the fans are pretty new so I don't think they're 'worn'.
Thanks!
PS: I've tried non-HP fans but as the BIOS has been hard-coded for specific RPM/voltages the server obviously refuses to boot.
server trys to boot every 20 or so seconds but imediatly fails
some times it gets to the boot screen before errors
the server is not geting hot all fans run
this just suddenly started happening
i had even touched it
ive tryed reseating everything but same thing happens
ive taken ram out etc no joy
Hello! I bought a new HP Proliant DL360 G4 a couple days ago, and it's setting the hdd (I only have one) to read-only, therefore I can't install an os on it. I have clonezilla (linux live enviroment) to work with.
The drive is in RAID 0 because I can't turn RAID off, and the only other thing that has been changed is that I've turned iLo off because I have no need for it. If you need any other info just ask
Thanks for helping -InVaLiD
Dears ;
we've been faced tomorrow morning to this error Runtime Fault, System Board, AUX/Main EFUSE Regulator 1 (01h) P12V Main/AUX Regulator 1 (02h) on HP proliant DL360 GEN 9 . i do some test to replace the power supplie by a new and nothing .
need help please .
Dear Sir
I am unable to Install Os on HPE proliant ML10 . i am getting error screen
Tenemos un servidor: HP Proliant DL380P Gen 8
En el cual se ha reportado un problema. Tiene un RAID 0 con 3 discos.
Uno de sus discos es un (653960-001) HP G8 G9 300-GB 6G 15K 2.5 SAS, el cual tiene una luz roja y en el software indica que ha tenido falla. Los otros 2 discos duros, son del mismo modelo y se encuentran bien.
Se ha reemplazado, el disco con fallas por un nuevo disco duro (652611-B21) HP 300GB 6G SAS 15K SFF 2." SC ENTERPRISE
Se ha vuelto a construir el RAID 0 satisfactoriamente.
Pero el nuevo disco duro sale instalado aparece una luz roja.
En el software de gestión no aparece ninguna alerta.
Además se ha empezado grabar información en el nuevo RAID correctamente.
Un técnico nos indicó que esto era probable porque se había colocado un nuevo disco duro y se tendría que actualizar el firmware de la controladora.
Agradecería su apoyo con esta confirmación o que solución podría darse.
We have a server: HP Proliant DL380P Gen 8
In which a problem has been reported. It has a RAID 0 with 3 disks.
One of its disks is a (653960-001) HP G8 G9 300-GB 6G 15K 2.5 SAS, which has a red light and in the software indicates that it has had a failure. The other 2 hard drives are the same model and are fine.
The failed disk has been replaced with a new hard disk (652611-B21) HP 300GB 6G SAS 15K SFF 2. "SC ENTERPRISE
RAID 0 has been successfully rebuilt.
But the new hard drive is installed a red light appears.
No alert appears in the management software.
In addition, it has started recording information in the new RAID correctly.
A technician told us that this was likely because a new hard disk had been placed and the controller firmware would have to be updated.
I would appreciate your support with this confirmation or what solution could be given.
We have a server: HP Proliant DL380P Gen 8, in which a problem has been reported.
It has a RAID 0 with 3 disks.
One of its disks is a (P / N: 653960-001) HP G8 G9 300-GB 6G 15K 2.5 SAS, which has a red light and in the management software indicates that it has had a failure. The other 2 hard drives are the same model and are fine.
Therefore, it has been replaced by a new hard drive (P / N: 652611-B21) HP 300GB 6G SAS 15K SFF 2. "SC ENTERPRISE
RAID 0 has been successfully rebuilt and information is already being saved.
But a red light appears on the new installed hard drive. (Attached image) (Box 2 - Bay 2)
No alert appears in the management software.
Is this because a new hard drive has been placed and the controller firmware needs to be updated?
I appreciate your answers or any solution to this problem.I have an HP ProLiant ML350 G6 Server, I want to add a second processor. I'm going to buy an Prosesor Intel Xeon X5690. Is this processor compatible with my server?
good GPU recommendations for my server?
I will use my server for computing
AN HP PROLIANT ML110 GEN 10 IS NOT DETECTING CONTROLLERS IN THE SMART STORAGE ADMINSTATOR
REFLECTING THE MESSEGE "NO CONTROLLERS DETECTED".
On a DL380 Gen 10 server with Smart Array P824i-p MR raid controller and RHEL 7.7 we encounter the following problem when trying to update the firmware of hard disks with SUM:
The driver provided by RHEL 7.7 (07.707.50.00-rh1) is even newer than the one provided by HPE (07.706.05.00-14
But even after installing the version provided by HPE (and restarting the server), the problem persists and the message does not change:
Dear All,
I am Installing Ubuntu in HP Proliant DL380 G5 server but the installation does not find any disk, I then tried to install Windows OS, the installatiion was successful, and then I further checked on the internet and found to install these drivers; HP Proliant Support Pack CD for dpkg-based distributions
I managed to download burn into the cd but booting does not detecting the cd.
How can I install these drivers or how can I install the Ubuntu?
