Hi
I have a DL380p G9 server and HPE ESXi 5.5 virtualizatin. The VMs are from w2008R2 to w2016.
Can I still use the latest SPP in terms of support for ESXi 5.5 or w2008R2 VM?
↧
SPP Version 2019.09.0 and ESXi 5.5 or w2008R2 compability
↧
ML30 Gen10 Drivers
Hi, add 3 1TB disks to the cage configured for RAID 5 all good.
However, HPE Windows Server 2019 Essentials does not recongise the disks, therefore, can't complete the install.
I have tried a number of drivers for the Storage controller but no luck.
The controller is the standard nothing special, thoughts on which drivers to use.
Thanks
↧
↧
PE ProLiant ML310e Generation 8 (Gen8) v2 HP SMART ARRAY IS NOT DETECTING HDD
Dear all,
my server PE ProLiant ML310e Generation 8 (Gen8) v2 is not detecting hp smart array for raid configuration and not even detetcing harddisk.
↧
DL 380 G5 boot from USB
Hi All,
i would like to install window server 2016 into this server using usb. unfortunately, this server not bring me go to select my usb. i already set the boot start from usb drivekey. Kindly help.
error geting from screen as below
attempting boot from usb drivekey (C:)
attempting boot from hard drive (C:)
error loading operation system
↧
Unexpected Restart
I have an HPE ProLiant DL380 Gen9 Server. approximately a month ago, this server is starting to shut down multiple times. this happened 4 or 5 times during the month. the Health LED is flashing amber every time it restarts. According to HPE, Health LED flashing amber means "System Degraded", I don't know what that means. what is the issue, and what should I do.
↧
↧
SATA CABLE FOR HPE PROLIANT ML110 GEN10 (P03685-425) SERVER
Good day,
Please I have a newly bought server HPE Proliant ML110 Gen10 (P03685-425).
Kindly recommend a suitable SATA cable that I can use to connect my SATA hard drive to this server.
Thank you.
↧
Looking for the iLO Amplifier Pack update (.bin) package
Does anyone knows where it is possible to find the iLO Amplifier Pack upgrade .bin file to upgrade an appliance from version 1.40 to 1.50 ?
Somehow i can't seem to find anything else besides the full appliance .ova
Thanks.
↧
HP proliant DL380
Hi,
I purchased HP proliant DL380 Gen10 am unable to install windows server 2016 due to the fact that,it cann't load the harddisk so as to enable to install the os.
Kindly i need your help
↧
Proliant ML350 G6 not booting from USB
I'm trying to install Server 2012 R2 onto a Proliant ML350 G6 server that our school has, but am running into a number of issues.
First I reset BIOS to system defaults, checked USB options were enabled and that External DriveKey was the flash option. I then created a drive in RAID, inserted a SErver 2012 R2 USB created using Rufus and booted the server. It got past POST then tried to boot from USB and got Red Screen with Illegal OpCode.
So I found download for SPP 2017.04, created a USB using HP USB Key Utility, tried to boot from it, but it doesn't recognise it and just says that its a non-system disk.
I've tried different USB's, different versions of USB Key Utility but nothing seems to work.
System Specs
Xeon E5520 CPU
12GB RAM
Smart Array P410i Controller
↧
↧
ML350 Gen10 Network errors
Hi there.
Recently installed a Proliant ML350 Gen 10, running VMware: HPE Customized Image ESXi 6.7.0 Update 2 version 670.U2.10.4.1. Using a single NIC for the moment, and the iLO interface is also connected.
We are monitoring the machine remotely, using Check_MK, and noticed that there are packet errors on both the network interface used for VMware, as well as on the iLO interface. The errors are inbound only.
On the main NIC we see slightly less than 1% of errors, on the iLO NIC about 10%.
The switch shows no errors at all.
While debugging in VMware, I noticed that all errors are Receive length errors, indicating packet size issues.
Checked the interface, switch, monitoring system, all are set for MTU 1500, so I would not expect to see packets over 1500 bytes long. Yet, when I run tcpdump on VMware, there are large packets arriving.
This is the only Proliant that shows this behaviour. We have other Proliants under our watch, but not the same models, and none show any symptoms similar to this one.
So I am thinking that the NICs in this machine maybe use offloading to reassemble the fragmented packets before handing these over to the OS. However, I couldn't find anything related to this in VMware, so I am first seeking advice here to see if anyone has seen this too.
Does this make sense? Or does anyone else have any other explanation or experience?
Thanks, regards,
Jaap
↧
Bootable HPSUM Switches for TPM
Is there a guide for editing the grub.cfg menu on the bootable HPSUM ISOs?
I see some switches like AUTOPOWEROFFONSUCCESS but was wondering if there were more switches for bypassing the TPM, powering off on failure, etc.
Thanks.
↧
iLO Amplifier Pack - No File Upload option for Baseline
According to the ILO Amplifier FAQ there should be an option to upload the files for a baseline using file upload but this option is not present. I have only recently setup the ILO amplifier and do notice that in any download I try I get version 1.50 when the latest is version 1.55 to my knowledge.
Is the version the issue and if so where can I get version 1.55?
↧
Can i install Windows 2008 R2 Standard Edition in ML 110 Gen 10 Server ?
We have a ML 110 GEN 10 server with Bronze 3104 processor .
is it possible to install windows 2008 R2 STD OS in this server ?
↧
↧
p816i-a Drivers for HP Proliant Windows Server 2016 installation
Hello,
I have a HP Proliant server that needs 2016 installed however, Windows cannot find the device drivers for the RAID controller in order to install onto the drives. Currently the server has 6 drives in RAID 10. Where can i find the drivers to this controller?
I've tried this link but it tells me that I dont have the correct permissions.
https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00018964en_us
Thanks in advanced,
Francisco
↧
ML350 GEN 10 memory 209 error
Hi I have a brand new server P11052-421 it came with 32Gb of Ram (P02052-091). I added 2 * 16Gb part number P00922-B21 (P03050-091) I put them in Dimm slot 10 and 12 as per memory map. The server see the 64Gb of ram but I am getting this error on boot up.
209 Unsupported Dimm Configuration detected installed dimm configuration does not support configured AMP mode system will operate in advanced ecc mode major code 0000003A minor code 00000000
I would really appreciate some advice.
↧
SNMP not showing Power Consumption for DL360 Gen10
Hi All,
we are monitoring DL360 Gen10 by snmpwalk method, I face issue with cpqHeFltTolPowerSupplyCapacityUsed ( 1.3.6.1.4.1.232.6.2.9.3.1.7 ) is just returning 0's
SNMPv2-SMI::enterprises.232.6.2.9.3.1.7.0.1 = INTEGER: 0
SNMPv2-SMI::enterprises.232.6.2.9.3.1.7.0.2 = INTEGER: 0
Any idea?
↧
Proliant ML380p and Noisy Fans
Hello, I'm having a problem with an ML380p I just bought refurbished (so it's not covered under HP warranty or anything like that, but I was hoping someone here could help me anyway).
I've read through the forums that a lot of people had problems with fans spinning at 100% even in cool conditions with low server load.
I'm having that same problem with my server. I've read through the forums and tried every solution I've found. I've upgraded the firmware. I've tried disabling iLO since people said it can be caused by iLO. I've made sure the BIOS settings is set to optimal cooling, which was the official solution to this problem in the help base. However, even with all of that done, all of my fans spin at max speed and are deafeningly loud.
I'm not getting any error messages at all, and I'm at wit's end. I've searched all over Google but I just can't find any solution other than the ones I've tried to no luck. Is there anyone else who has solved this problem by another means than the ones I've already listed and tried?
↧
↧
Parity Initialization Progress - CLI Created Logical Volume
Servus Community,
Yesterday we created a new logical volume in the Command Line Interface with the following command:
/opt/smartstorageadmin/ssacli/bin/ssacli ctrl slot=0 create type=ld drives=1I:1:17,1I:1:18,1I:1:19,1I:1:20,1I:1:21,1I:1:22,1I:1:23 raid=6
The volume was immediately visible in the web GUI of our ESX 6.5 and we were able to create a new data store there. This is also usable and we already install some VMDKs there.
What we don't know is the status of the Parity Initialization Progress display, which is still at 0%. For another volume, which already existed and was not created with the CLI, but in the controller BIOS, it will be displayed there: Initialization Completed:
For the new, CLI created volume we got this output:
---snip---
/opt/smartstorageadmin/ssacli/bin/ssacli ctrl slot=0 ld 2 show
Smart Array P440ar in Slot 0 (Embedded)
Array B
Logical Drive: 2
Size: 5.46 TB
Fault Tolerance: 6
Heads: 255
Sectors Per Track: 32
Cylinders: 65535
Strip Size: 256 KB
Full Stripe Size: 1280 KB
Status: OK
Unrecoverable Media Errors: None
MultiDomain Status: OK
Caching: Enabled
Parity Initialization Status: In Progress
Parity Initialization Progress: 0% complete
Unique Identifier: 600508B1001C4828A9D9A8C1870E0F8A
Logical Drive Label: 06C4F007PDNLH0BRH78D1217CE
Drive Type: Data
LD Acceleration Method: Controller Cache
---snap---
And for the existing, controller BIOS created Volume, we got this output:
---snip---
[root@localhost:/opt/smartstorageadmin/ssacli/bin] ./ssacli ctrl slot=0 ld 1 show
Smart Array P440ar in Slot 0 (Embedded)
Array A
Logical Drive: 1
Size: 6.55 TB
Fault Tolerance: 6
Heads: 255
Sectors Per Track: 32
Cylinders: 65535
Strip Size: 256 KB
Full Stripe Size: 1536 KB
Status: OK
Unrecoverable Media Errors: None
MultiDomain Status: OK
Caching: Enabled
Parity Initialization Status: Initialization Completed
Unique Identifier: 600508B1001C0FC35B29727B79F53993
Logical Drive Label: 01B0CE71PDNLH0BRH78D12FD28
Drive Type: Data
LD Acceleration Method: Controller Cache
---snap---
We assume that the output 0% is incorrect, but it would be interesting what we have to do, to update it, to the current correct value...
Thx & Bye Tom
↧
Management Processor Status. Minor problem
Hey,
in HPE i have 2 minor messages (yellow).
-Management Processor Status
-There is a minor problem that is causing limited interference
when i connect to the ilo, there is no error. SNMP Settings are correct.
we have different proliant version (dl380p gen8 -> ml350 and so on).
The Message is arbitrarily and not on one hardware version.
what could be the problem?
thank and regards
daniel
↧
Unable to upgrade oneview 4.20.01-0380241 to 5.00.00.02
Hi!
I've been trying to upgrade my oneview installation from 4.20.01-0380241 to 5.00.00.02.
Unfortunately my certificate has expired, and it the installation kind of stops due to that. (I Assume)
"The appliance update has failed because the appliance web server certificate is expired."
"Resolution Regenerate a new appliance self-signed certificate or re-import a new CA signed appliance certificate. Then retry update."
Fine, i will generate a new certificate, but i receive the error when importing the certificate:
"Issue Unable to trust the incoming certificate.
The CA certificate with common name %My CA name% used for signing the incoming certificate with common name %My Common Name% is not a trusted certificate.
Resolution
Add the certificate and retry the operation. To add the missing certificate you can use import certificate option under Settings -> Security -> Manage certificates."
I've found a different thread where it says that to import the appliance certificate, i will have to do it from Settings - Security - Actions - Import Appliance Certificate (Which is how i try to import the certificate now)
Also, i have noticed that the "Application Certificate" when browsing certificates has changed to a self-signed certificate with what looks like some default settings. (Happened after i attempted to upgrade the appliance)
↧