How can I deploy this to Debian?
https://support.hpe.com/hpsc/swd/public/detail?swItemId=MTX_6d3a7434a68f4b0ab8d143fdb7
↧
** CRITICAL ** Supplemental Update / Online ROM Flash Component for Linux - EF0300FATFD, EF0450FATF
↧
DL360 Gen10 + Windows Server 2012 unable to boot into
Hi all
Need help with this one, got a DL360 Gen10 Server running 1x 240 SSD supplied by HPE (VK000240GWTSV)
The BIOS picks up and installs Windows Server 2012 R2 fine via the Inteligent Provisioning terminal
For a while everything going okay, but somehow out of the blue after a few days something causes the machine to restart and puts the Windows boot Loader into 'automatic repair' mode, in which causes the drive in question to no longer be picked up.
I go into the shell and run diskpart, which the drive in question is not listed
I can still see the SSD in the RAID Configruation screen (although not configured as a RAID Drive), and I had plugged the drive into my Windows 10 laptop to see if the data is still there (which it is), however unless I reinstall the OS (which I am trying to avoid), i am stumped
Any ideas?
Also hypothetically - could a 3rd party NIC cause this to occur? or have I got a lemon
↧
↧
HP dl360g9 server problems------HP DL360G9服务器问题
每次启动服务器系统时间都比正确时间慢8小时然后校准以后几分钟又会出现比正常时间慢8小时，主板电子是新换的还不是换了一次换了很多次都不能解决，想知道是不是需要在BOSS里面设置时间还是哪里又问题，系统也装个N个了都不能解决，希望大神给解决下-------------------- -------------------------------------------------- -----------------------------Every time you start the server system, the time is 8 hours slower than the correct time. After the calibration, a few minutes later, the time will be 8 hours slower than the normal time. The main board electronics are new or not replaced once and many times, which can't be solved. If you want to know whether you need to set the time in the boss or where the problem is, the system can't be solved even if you install n of them. I hope God can solve it
↧
ProLiant DL360 Gen10 and NVIDIA Tesla T4
Hi,
I want to know if it is possible to in a ProLiant DL360 Gen10 8SFF with 2 processors, attach 2 NVIDIA Tesla T4 16GB and 16Gb Dual Port Fibre Channel HBA? Because the GPUs will use the PCIe.. and Fibre Channel HBA also will need a PCIe. It is possible?
Regards
↧
2 GPUs on dl380 g7
Hi
Im trying 2 install 2 gpu cards on my dl380 g7
#1 Quadro k620 for computation
#2 Quadro nvs 310 for monitor output.
I connected the k620 to the riser card and the nvs 310 using an x16 to x1 molex powered riser directly to the motherboard (without connecting any extra power to the molex)
When i tried to start the system, the system health led turned red and the system didnt start. But things got back to normal when i removed the 2nd gpu.
Any idea what the problem is and how i can install both GPUs?
Im trying 2 install 2 gpu cards on my dl380 g7
#1 Quadro k620 for computation
#2 Quadro nvs 310 for monitor output.
I connected the k620 to the riser card and the nvs 310 using an x16 to x1 molex powered riser directly to the motherboard (without connecting any extra power to the molex)
When i tried to start the system, the system health led turned red and the system didnt start. But things got back to normal when i removed the 2nd gpu.
Any idea what the problem is and how i can install both GPUs?
↧
↧
HP proliant 380P server not able to boot, stuck in boot cycle
Hi guys
I have below configurations, I have installed vmware 6.5 custom image (https://my.vmware.com/web/vmware/details?downloadGroup=OEM-ESXI65U3-HPE&productId=614)
Now I have successfully installed the vmware but when I reboot after the installation(after pressing F1 to continue) it's keep looking for boot device and stuck in boot cycle. Never loads the OS. Could you please help me I would really appericiate, I have tried many different things still struggling here, need help.
HP ProLiant DL380p G8 8 bays
2*E5-2620 12 Cores
Memory-64GB 8x8GB
HDD-1.8TB - 3x 600G (RAID 5)
P420i
4*1GB Network Ports
System ROM P70 05/24/2019 iLO Firmware Version 2.55 Aug 16 2017
Thanks
LP
↧
ProLiant DL380 Gen9 SPP Upgrade
Hi, all.
We are planning to upgrade the SPP of our servers using the p26940_001_spp-2020.03.0-spp2020030.2020_0319.22
Just want to ask everyone if someone already tried it on a vSAN Cluster and if there's any compatibility issue on it?
Thanks in advance.
↧
HP proliant 380P server not able to boot, stuck in boot cycle
↧
HP ProLiant Micro Server Gen10 shuts itself down
↧
↧
Restart the server HP DL380p G8 after turning on immediately
Hello,
When turning on the server (HP DL 380p G8), after displaying the BIOS version the server immediately will reset.
I don't have any option to choose ( for example F8, F9, F10,...)
what I should to do?
↧
how to change HPE server (ilo-5 ) Boot order using the redfish API for legacy bios?
Hi Guys,
I have HPE 10 Gen server and i am looking for exact json parameter to be passed using the redfish API to configure the below two thing
1- Bios boot mode should be configured in legacy mode ( default is UEFI mode )
2- boot order
- PXE
- HDD
- CD
- Usb
3- how to change the ilo factory default password using API from out of band management connected linux server.
↧
HP ProLiant DL380 Gen9 - Replacing Smart Array P440ar
Dear Community,
I´m in trouble with a Smart Array P440AR Controller embedded in a DL380 Gen9 machine due to a reported cache memory failure (Error 1797: Write Back Cache Backup Previously Failed. Caching is permanently disabled. Action: Replace the Cache Module).
At first, I´ve upgraded the firmware to the latest version (V7.00) and renewed the battery. Then tried to recover the cache module via Smart Storage Administrator. The function ends up with "Recover failed due to an unknown error".
The server runs fine so far, but with cache disabled.
Because the cache module seems to be soldered on the controller board, I´ve obtained a new replacement P440AR controller, which has Firmware V4.52 programmed by factory.
Could you please help me and give hints on how to >safely< replace the board:
- Can I connect the Disk-Set without risk for data to new 4.52 controller, altough it has been in access by the old (fw 7.00) controller before?
- Or is the a procedure to upgrade the new controller to fw 7.00 without having the Raid-Set connected (Set is Server´s Boot-Device), and connect the Disks for the first time afterwards? Thought about that it might be possible to use a bootable Windows-on-DVD distribution via S-ATA DVD-drive while the Raid-Set remains disconnected, just to execute the fw upgrade installer package.
Many thanks in advance, any support would be much appreciated,
bsd
↧
HPE ML30 Gen10 unable to see HPE 240GB SATA MU M.2 2280 DS SSD
Purchased a ML30, 4x 4Tb HDD and a HPE 240GB SATA MU M.2 2280 DS SSD. All HP breed.
I've tried just about all I can see in the 'bios', and cannot get the SSD to be visible anywhere.
Tips and tricks appreciated, before I give up and send it all back and by an Intel box. like I used too.
↧
↧
iLO did not detect the Agentless Management Service
Hello all
Anyone can explain this iLO message
Thank you
↧
ESXI Power Module - Warning with Voltage
Hi,
I was wondering if anyone can help me with that Proliant - ESXI problem.
I am running ESXI 6.7 on my ProLiant DL160 G6. Basically everything is fine and VMs are running smoothly!
However, my ESXI gives me a warning like that:
Power Module (DC-to-DC) 6 P1V5_DDR3_CPU2 --> 1.35 Volts (red flag warning)
Power Module (DC-to-DC) 3 P1V5_DDR3_CPU1 --> 1.34 Volts (red flag warning)
Now I have no idea at all, if that is a problem or not....
I already swapped my RAM with other modules but the error stays the same. Is that Voltage level a problem? Should I be worried?
I would be happy for any hint or intel, as I am not really big into details about that server hardware. I am basiclly only running VMs on that machine and am pretty happy with it so far. But now I am concerned about possible risks...
Thanks in advance!
Cheers
Mario
↧
Installed Clear OS on HP DL60 G9. Not seen at boot time.
I have installed ClearOS on my HPE DL60 G9. I installed it as a direct boot from USB since intelligent provisioning would only give me the option to install from DVD (Which this machine does not have)
Now, when I boot it doesn't see the OS on drive one but instead skips through to a PXE boot and gets stuck. It eventually reboots with the same result repeatedly.
I saw he drive light spinner on drive one running when the installation was being done.. What am I missing?
This is my first HPE server and my first server in general.
This is a two drive system. I only selected on to install to and cleared the hardware RAID configuration.
↧
SAS disk on dl360e g8 not recognized without raid card
Hello, I bought 2 HP sas disk with the racks they are not recognized I think the raid card does not support me sas but the server is obligatorily obliged to pass by a card of the type b420e, I tested with a SATA SSD it is recognized but the integrated raid card does not recognize it, I do not understand the problem I would like explanations, thank you: D
A video when I plug the disc: https://youtu.be/Fn4w3OdXhw8
A video when I plug the disc: https://youtu.be/Fn4w3OdXhw8
↧
↧
DL380p G8, RAID 10 strange activity lights
Hello Community,
My name is Bogdan and i am new here, so please be gentle
I have recently bought 2 DL380p G8 with 12 LFF disks and I see strange behaviour on activity lights.
First off all you have to know that I am using nonHP disks but new ones and I dont have any problem in ILO or on POST, all the hard disk are recognized ok and they work perfect.
When I create RAID 10 between 6 x 2TB SATA disks, activity ring is running constantly even after 3-4 days (so it is not initialization), NON-STOP, it doesn't stop like on RAID 1 or 5 where it stays off and goes on only if it have activity. This issue is present with empty array in RAW format and also when I create NTFS/ReFS volume. I know some will say that it is because I use nonHP drives but:
- this doesn't happen if I use RAID 0 on each drive or all in a RAID 0 array ( here, activity ring it goes on only when there is activity) so there are no signaling problems in RAID 0
- it happens to show some activity on disks if I use RAID 5 but not so much like on RAID 10
- it appears there is a RAID 10 specific behaviour.
- all the other RAID arrays ( 0 and 1 ) doesent show any activity ( SSD and hard drives )
What I want to know:
do you have the same problem with activity ring in RAID 10 config?
is this only a activity light problem from firmware/caddy or there is real work from raid controller to hard disks?
can i use some commands in CLI to see if the controller ( P420i ) it is actualy doing something with hard disks from the array or maybe it is just a signaling problem?
Every where I look ( ILO, Insight manager, RAID config. software ) everything is good or OK, no problems, nothing,only Activity Ring that it circles permanently. I am afraid not to damage or create fatigue on hard drives and reduce there life time.
I post my firmware versions but I think it is all new or what I found to upgrade.
iLO 2.73 Feb 11 2020 Intelligent Platform Abstraction Data 1.01 Intelligent Provisioning 1.71.19 Power Management Controller Firmware 3.3 Power Management Controller Firmware Bootloader 2.7 Redundant System ROM P70 02/10/2014 SAS Programmable Logic Device Version 0x0C Server Platform Services (SPS) Firmware 2.1.7.E7.4 Smart Array P420i Controller 8.32 System Programmable Logic Device Version 0x32 System ROM P70 05/24/2019 System ROM Bootblock 03/05/2013
Thank you very much for your time and expertise!
↧
Configuring B120i Controller
Hey folks.
I've been trying to configure B120i in my DL380e Gen8 for a few hours now. I'm trying to configure it with one 120GB SSD (server is used for testing purposes).
I booted into Intelligent Provisioning. When I select the controller, I'm greeted with the following errors (please check picture). Cables are correcly connected and SSD is in correct bay.
Are there any solutions to this?
↧
Deploy SPP bundle with SCCM application, how to control if the deployment is a success?
Hi, Deploy SPP bundle with SCCM application, how to control if the deployment is a success?
I have made several OSD deployment of Windows Server to HPE proliant servers with success. I just have a package in the TS that trigger the "hpsum_bin_x64.exe". I have not had any special control, I just workt verry well in general.
Now have the hardware folks asked if I can find a way to deploy the HPE during service maintenance window for our servers. They use OneView it works well for administration of HPE servers, but not deploying update SPP. I have also looked in to deploy with the new third party updates and cant find this a option for now. It is till a hack for HPE SPP. and the SPP is to old.
Then with SCCM I can use Application mavbe in a application TS for upgrade old SPP.
I will build an SCCM Application for test, but I would like to understand if the SPP upgrade is finish with success or not and bult in a detection for this.
So how to check SPP installation, logs apps..?
↧