Quantcast
Channel: ProLiant Servers (ML,DL,SL) topics
Viewing all 10362 articles
Browse latest View live
↧

iLO4 v2.75 - Disabling 'Enable Active Health System Logging' reverts to enabled after iLO reboot.

October 23, 2020, 5:06 am
$
0
0

Hello,
I have 2 DL380Gen8p's for my homelab and to save the iLO NAND from wear and tear I would like to disable 'Active Health System Logging'.

I did disable (on both servers) 'Active Health System Logging' but I do notice that after a 'reset' (reboot) of the iLO subsystem the 'Active Health System Logging' keeps enabling itself.

I think this wasn't the case with an earlier firmware but I am too lazy to revert

Does anybody else with a Gen8/9 (both iLO4) with firmware v2.75 see this same behavior?

Regards,
Arian!

↧
Search

NVMe drives not detected in DL360 Gen9 server

October 23, 2020, 10:11 am
$
0
0

I have a DL360 Gen9 server with the 2 bay NVMe enablement kit.  I'm trying to use 2 Samsung PM983 SSD drives in them but the system seems to refuse to recognize them.  On power on the lights flash for a bit and then turn off.  If I press the power button on the drive carrier later the lights blink, but never go solid.

I was able to use some Intel NVMe drives in a DL380 and so was hoping I would not have to use HP drives, but perhaps there are some other requirements I'm not aware of?  Thanks.

↧
↧

Hp dl 380 g7 stuck on hp proliant logo after cache module swap

October 23, 2020, 12:27 pm
$
0
0
So I swapped the cache module from a 512mb to a 1gb module in my dl380 g7 as the battery died and swelled and upon putting the new one in I'm stuck on the hp Proliant logo with the led on the motherboard showing CR4 and CR5 lit. As far as I can tell this says an operation is in progress on the p410i but I've left it for half hour now no change with no drives plugged in either. Any ideas anyone I tried plugging the old cache module in again but same thing.
↧

ML350p G8 - Error Provisioning

October 24, 2020, 1:15 am
$
0
0

Hello,
I want to install Windows Server 2016 on a ProLiant ML350p Gen8.
First I have updated the server with the SPP P03092, Gen8.1, SPPGEn81.4.iso
During provisioning I load the ISO file via the ILO console. But in the menu I only see Windows Server 2012 R2.
How can the correct server version be displayed in the menu?

Many thanks.
Markus

↧

ProLiant DL60 Gen9 Server Critical Faults

October 25, 2020, 3:48 am
$
0
0

Hi,

My ProLiant DL60 Gen9 Server won't startup anymore so I logged into ILO to discover a number of critical faults. Can somebody point me in the right direction as to what is wrong with the server? 

  • Server Critical Fault (Service Information: Power On Fault, Power Backplanes, Power Backplane 1 (04h))

  • Server Critical Fault (Service Information: Power On Fault, System Board, P12V Main/AUX Regulator 1 (04h))

  • Server Critical Fault (Service Information: Power On Fault, Memory, CPU 1 Memory Channels 1-4 (10h))

  • Server Critical Fault (Service Information: Power On Fault, System Board, P12V Main/AUX Regulator 1 (04h) P5V/P3V3/Chipset/AUX Regulators 1 (01h))

  • Server Critical Fault (Service Information: Runtime Fault, Memory, CPU 1 Memory Channels 1-4 (10h))

Also, I don't have any warrenty left for this server. 

Thanks

↧
↧

DL380 g9 SPP update

October 25, 2020, 12:38 pm
$
0
0

Hello,

I am trying to update the DL380 g9 that I have. Once It runs the analysis of the system. I get 2 optional and 1 required update. I am getting 2 different errors though. I am trying to install is 2020.09.0. Which from what I thought in reading is for gen 9 and gen 10 Proliants. How should I proceed?

First is

There is a TPM detected on this system. Saying talking about saving backup keys, but I am not using Bitlocker. System is on ESXI Machine 

 

Second 

Warning - The selected Firmware Baseline is not supported for the given server. It is not recommended to continue with the updates using this baseline. Please select a different supported baseline for this server.
To proceed with the updates using this baseline at your own risk, select Ignore Warnings option.

↧

iSCSI boot Proliant gen10 using Software Initiator an linux target

October 26, 2020, 9:34 am
$
0
0

Hi All,

Has anyone tested booting Proliant  ML or DL Gen9 or Gen10 server from linux iSCSI target using Software Initiator? With no iSCSI dedicated NICs. ex. P11051?

I'm stuck at UEFI initialization with IML entry:

[UNKNOWN] 69 iSCSI Error - iSCSI login failed.

And target logs:

Oct 26 16:00:31 XXX tgtd: login_start(499) Target iqn.2015-10.com.XXX is RDMA, but conn cid:1 from iqn.2015-02.com.hpe:uefi-XXX is TCP Oct 26 16:00:31 XXX tgtd: conn_close(101) connection closed, 0x1e9b208 1

Target config as follows:

Target 3: iqn.2015-10.com.XXX System information: Driver: iser State: ready I_T nexus information: LUN information: LUN: 0 Type: controller SCSI ID: IET 00030000 SCSI SN: beaf30 Size: 0 MB, Block size: 1 Online: Yes Removable media: No Prevent removal: No Readonly: No Backing store type: null Backing store path: None Backing store flags: LUN: 1 Type: disk SCSI ID: IET 00030001 SCSI SN: beaf31 Size: 53687 MB, Block size: 512 Online: Yes Removable media: No Prevent removal: No Readonly: No Backing store type: rdwr Backing store path: /dev/XXX Backing store flags: Account information: ACL information: ALL
↧

HPE Ultrium 7 15000 issue on Windows Server 2019 Standard

October 22, 2020, 4:06 pm
$
0
0

 

How am I new to this forum ... I hope you can help me ...
We have a Proliant DL360 server with windows server 2019 standard and in this we have a Backup software called Veritas, we have a physical HP Ultrium 7 - 15000 Tape drive connected to the server ... the problem is that windows if it detects the Tape but Veritas does not reconnects the tape (within the software it puts the following message "Tape Drive 0001 (No Media)" but the status of it is Online but it still does not detect the tapes entered this when we carry out a catalog and an inventory ... it is a problem of driver or update the firmware of the tape ????

↧
Search

HPE Proliant DL360P Gen8 Cache module status - failed

October 27, 2020, 1:22 am
$
0
0

Good morning HPE Community,

I have a problem with DL360P Gen8, some time ago, we saw ILO reporting an issue - Cache module status - failed. After reading posts on community, and contact with support on my country, suggestion was to change a cache module battery - after replace battery, nothing change.

Server is after warranty, so i decide to write on community - i was thinking about update firmware of HP Smart Array P420i controller - it has v.3.22 firmware, but i do not know how i must to do this.

Anybody can send me step by step guide how to update firmware, can i update only controller firmware, or i must update all (ilo, bios, a then controller).

Some info about my server:

System ROM: P71 08/20/2012
ILO fv: 1.13 Nov 08 2012
System ROM Bootblock: 03/11/2012
Smart Array P420i Controller: 3.22
Power Management Controller Firmware :3.0
Power Management Controller Firmware Bootloader: 2.7
Server Platform Services (SPS) Firmware: 2.1.5.2B.4

I'm adding an screenshot of smart array controler.
Smart-array-p420i 

I have a knowlage about DELL server, in HP servers i'm new. Thank you for alle comments.

Best regards.
Adrian

↧
↧

HPSM login Issues

October 27, 2020, 2:07 am
$
0
0

Hi All, 

We are facing login issues on HPSM on server DL380 Gen9 . After our observation we found that config file has removed our admin group from config file after reboot. Not sure why this happening and this issue randomly increased on other servers as well. So we raised case with HP team they suggested to update HPSM version on servers but with lower version on other servers its working  fine.

 

Please provide your valuable input to fix this this issue.

 

↧

Proliant DL 380e G8 RAID 1+0

October 27, 2020, 7:16 am
$
0
0

Hello everyone, I could use some experience help. I have bought a HP P/N 641552-001 300g HD for this server and the new HD won't rebuild my RAID 1. I have read online that I should be able to hot swap and so I did. The drive, when done, show an all amber solid light.

I can not attached jpegs of what shows in iLO 4. the system board model lists HP DynamicSmart Array B120i. Controller on Slot 2 HP Smart Array p420 controller. It is the second HD that went bad. iLO 4 shows

Any help would be appreciated,

↧

232 dimm initialization error

October 27, 2020, 2:45 pm
$
0
0

Lost power, server shutoff

 

Upon trying to power back on I am met with following errors  "232 dimm initialization error" 

↧

how to replace hdd in server prolaint dl380 G8?

October 28, 2020, 12:39 am
$
0
0

hello. smart array p420i is configured and raid as well. in storage administrator, status showing 01 hdd pridected to be failed very soon. so i need to replace fault.y hdd with new one, please guide me to replce hdd

 

 

 

↧
↧

iLO webpage seems to fail to load at time, iLO reset fixes it

October 29, 2020, 9:08 am
$
0
0

Guys,

Does anyone else get this. I seem to get it on quite a few differnet versions of iLO, so i can't see a trend, but basically the iLO for one server will work one day, and then i'll see an error in OneView saying unsable to commniucate with server. And when i try to load the web page, i get nothing is displayed. 

I've found I can 99% of the time putty to the iLO, and from there i can do a cd /Map1 and then reset.

This normally makes ther server connect to oneview again and the webpage now loads as well.

Ideally i'd like not having to do this too otfen, any ideas why this is failing? I've not seen others complain about this, so it makes me wonder if its something on my network that could cause the webpage part of the iLO to fail

Thanks

↧

ML310 G8 iLO Firmware update no bueno

October 29, 2020, 10:51 am
$
0
0

Morning,

I've tried locating a new firmware for subject server. All say no device supported

My present iLo firmware is 1.51  dated June 16, 2014

Any comments welcome

↧
Search

HP 360p gen 8 PCIe NVME U2 sff-8639

October 29, 2020, 12:02 pm
$
0
0

Hello. Please forgive me in advance. I write through translator.

I have a DL360p server and I want to connect an NVME drive via a PCI x4 adapter to a PCIx16 slot. NVME drive WD SN640. When installing, I get an error ILO4 related to:

Uncorrectable PCI Express Error (Embedded device, Bus 0, Device 0, Function 0, Error status 0x00100000)

And the red button on the case is on. I tried another PCIeX16 adapter. But the problem is exactly the same. An error is written in the OS itself:  NMI: IOCK error (debug interrupt?) for reason 71 on CPU 0

Then the system is loaded and running. Tried running WIndows. There the blue screen of death flies out and it is impossible to put it. A separate intel s3700 SSD is used as a boot drive

Please help, maybe you need a special setting for NVME? My friends have tested PCI-M2 and everything starts fine for them. But with U2 problems ...... Thanks

↧

ML30 Gen10 and esxi 7.0 gpu passthrough problems

October 29, 2020, 7:24 pm
$
0
0

For a while, I've been wanting to passthrough an Nvidia Quadro P400 to a guest os.
I've updated from 6.7.0u2 to 7.0.1
(HPE-ESXi-6.7.0-Update2 to (Updated) HPE-Custom-AddOn_701.0.0.10.6.0-40)

In 6.7.0u2, Linux guest could see the GPU, but not "correctly" (nividia-smi not reporting card, but shows up with lspci)

In 7.0.0u1, the guest won't even boot with the passthrough (see below errors)

I've read about the passthrough changes in 7.0 and have created a new ESXi 7.0 U1 virtual machine from scratch.

  • The GPU is marked as active passthrough in the host hardware
  • The VM is configured with UEFI bios
  • I've added the GPU as a "Dynamic PCI device"
  • I've reserved all the guest OS memory

  • This GPU only has 2Gb...so nothing fancy there in memory allocations.
    This card is max 30 watts and no "extra" power connections...seems to work ok

I see nothing in the logs that would explain the failure.

2020-10-22T23:13:21.121Z| vmx| I005: DICT pciPassthru0.allowedDevices = "0x10de:0x1cb3,0x10de:0xfb9"
...
2020-10-22T23:13:21.410Z| vmx| I005+ Power on failure messages: Module 'DevicePowerOn' power on failed.
2020-10-22T23:13:21.410Z| vmx| I005+ Failed to start the virtual machine.
2020-10-22T23:13:21.410Z| vmx| I005+
2020-10-22T23:13:21.411Z| vmx| I005: Vix: [mainDispatch.c:4200]: VMAutomation_ReportPowerOpFinished: statevar=0, newAppState=1870, success=1 additionalError=0
2020-10-22T23:13:21.411Z| vmx| I005: Transitioned vmx/execState/val to poweredOff
2020-10-22T23:13:21.411Z| vmx| I005: Vix: [mainDispatch.c:4200]: VMAutomation_ReportPowerOpFinished: statevar=0, newAppState=1870, success=0 additionalError=0
2020-10-22T23:13:21.411Z| vmx| I005: Vix: [mainDispatch.c:4238]: Error VIX_E_FAIL in VMAutomation_ReportPowerOpFinished(): Unknown error
2020-10-22T23:13:21.411Z| vmx| I005: Vix: [mainDispatch.c:4200]: VMAutomation_ReportPowerOpFinished: statevar=0, newAppState=1870, success=1 additionalError=0
2020-10-22T23:13:21.411Z| vmx| I005: Transitioned vmx/execState/val to poweredOff

As soon as I remove the GPU from the VM, the VM will power up without issue.
I feel I have to be missing something obvious as this "should work", but I'm currently at a loss.

TIA for any help.

 

↧
↧

Big trouble with DL380 G8 accessing Intelligent Provisioning or Storage Administration

October 30, 2020, 9:40 am
$
0
0

Hello, 

since hourse we try to install windows server on a HP DL380 G9. Our problem is that we can not access Intelligent Provisioning or Storage Administration. In both cases we get error messages or screen is freezing etc. on post screen everythink looks good. Hardware check is fine, ILO Webpage we can access without any issue, but the important functions to create a raid1 before install Windows is not possible. The server is running with all latest firmwares. It is really very frustrating, we have 3x DL380 G8 and never had problems, now we have 2x DL380 G89 and one of them make the problems now

System: 

  1. 2x E5-2680v4
  2. 512GB DDR4
  3. HP P840 with 4GB Cache and BBU 
  4. 2x 500 Watt PS

Software / Firmware 

  1. HP P840 -> V7.0
  2. ILO4 -> 2.75b
  3. BIOS -> P89 2.76
  4. Intelligent Provisioning -> 2.82.9

When I click F10 -> the system is loading the nex selection page, before the page is displaying where I

can select the Intelligent Provisioning or Storage administration, I can see on a black screen a error message:

error: no such device: HPEZCD260

When I try to access the Intelligent Provisioning I get an Firefox error and nothing happened. When I try to load the Storage Administration I get a dark blue screen and nothing happened. In some cases when I attach SSDs I get a black screen with error messages regarding mounting issue and or maintendence mode mesages

Can anyone help here please I really do not know any more

 

firmware overview.PNGhpe-ip-firefoxerror.PNG

 

after starting the storage administration with one attached drive on 12bay backplane

storage-administration.PNG

 

↧

HP6125XLG and security-logfile

October 31, 2020, 1:17 am
$
0
0

Dears,

I need access to security-logfile.

When I try to display security-logfile summary, I can see below info:

<HP6125XLG_XXX>display security-logfile summary

Permission denied.

<HP6125XLG_XXX>

Could you support me how access to this security-logfile?

regards

Alpork.

↧

Help with DL360e Gen8 - Possible Raid controller failure?

October 31, 2020, 3:18 pm
$
0
0

Hi All,

Ive trawled the forum but cannot find an answer to my problem. We have a DL360e Gen8 sever running Windows 2012 Server with 8 disks in a Raid. (Single processor E5-2403, 8GB RAM, B320i Raid Controller) that has been hanging a lot recently. Ubenknown to me, users have been forcing it off and on again when it was running slow for the past few weeks! Today it was restarted and now wont reboot.

When the server is started it is slow to boot, finally gets to the windows logo and then we get the BSOD (no error numbers or messages). Ive been trying all day to get it going again but I think the Raid controller might have failed. If I go into the iLO overview and click on strorage, it says there is no smart array installed and when the server is booting (with the windows logo showing) all the drives turn off, I get the blue lights then all flash as the disks start up again just before the BSOD.

Would you guess that the Raid controller has failed? or maybe the power supply?

↧
Viewing all 10362 articles
Browse latest View live
Search